LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> 4Runner Limited, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 2 (Automatic Transmission System (A750E) - Service Information) >> Valve Body Assembly >> Inspection [08/2015 - ] >> Procedure

Inspection [08/2015 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSPECT SHIFT SOLENOID VALVE SR 
    GTY711935Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      Shift solenoid valve SR connector terminal - Shift solenoid valve SR body 20°C (68°F) 11 to 15 Ω
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Shift Solenoid Valve SR)
    2. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK

      Measurement Condition Specified Condition
      • Battery positive (+) → Shift solenoid valve SR connector
      • Battery negative (-) → Shift solenoid valve SR body
      		 Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

  2. INSPECT SHIFT SOLENOID VALVE SL1 AND SL2 
    GTY704380Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Shift Solenoid Valve)
    2. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK

      Measurement Condition Specified Condition
      • Battery positive (+) with a 21 W bulb → Terminal 1
      • Battery negative (-) → Terminal 2
      		 Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

  3. INSPECT SHIFT SOLENOID VALVE SLT AND SLU 
    GTY735284Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 -2 20°C (68°F) 5.0 to 5.6 Ω
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Shift Solenoid Valve)
    2. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK

      Measurement Condition Specified Condition
      Battery positive (+) with a 21 W bulb → Terminal 2 Battery negative (-) → Terminal 1 Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

  4. INSPECT SHIFT SOLENOID VALVE S1 
    GTY702931Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body 20°C (68°F) 11 to 15 Ω
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Shift Solenoid Valve S1)
    2. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK

      Measurement Condition Specified Condition
      • Battery positive (+) → Shift solenoid valve S1 connector
      • Battery negative (-) → Shift solenoid valve S1 body
      		 Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

  5. INSPECT SHIFT SOLENOID VALVE S2 
    GTY720453Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body 20°C (68°F) 11 to 15 Ω
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Shift Solenoid Valve S2)
    2. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK

      Measurement Condition Specified Condition
      • Battery positive (+) → Shift solenoid valve S2 connector
      • Battery negative (-) → Shift solenoid valve S2 body
      		 Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

scientia non olet · About LEMON Manuals