LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2015 >> Prius V Two >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge / Display - (Diagnostics - Introduction) >> Meter / Gauge System >> Data List / Active Test [11/2014 - ] >> Data List / Active Test [11/2014 - ]

Data List / Active Test [11/2014 - ]

  1. DATA LIST 
    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Warm up the engine.
    2. Turn the power switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the power switch on (IG).
    5. Turn the Techstream on.
    6. Enter the following menus:
      1. for Combination Meter: Body Electrical / Combination Meter / Data List.
      2. for ABS/VSC/TRAC: Chassis / ABS/VSC/TRAC / Data List.
      3. for Engine and ECT: Powertrain / Engine and ECT / Data List.
      4. for Main Body: Powertrain / Main Body / Data List.
    7. Read the Data List according to the display on the Techstream.
      COMBINATION METER

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Tail Cancel SW Tail cancel switch / OFF or ON OFF: Tail cancel switch off Dimming of dash lights is possible
      ON: Tail cancel switch on Dimming of dash lights is canceled
      P-Seatbelt Buckle SW Front passenger side seat belt buckle switch / OFF or ON OFF: Front passenger side seat belt unfastened -
      ON: Front passenger side seat belt fastened
      Vehicle Speed Meter Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed -
      Coolant Temperature Engine coolant temperature / 0 to 127.5°C (0 to 261.5°F) After warming up: 75 to 100°C (167 to 212°F) -
      Timer Switch M on Combination Meter Minute adjust switch (Hazard warning signal switch assembly) / OFF or ON OFF: Minute adjust switch not pressed -
      ON: Minute adjust switch pressed -
      Timer Switch H on Combination Meter Hour adjust switch (Hazard warning signal switch assembly) / OFF or ON OFF: Hour adjust switch not pressed -
      ON: Hour adjust switch pressed -
      Timer Switch 00 on Combination Meter Second adjust switch (Hazard warning signal switch assembly) / OFF or ON OFF: Second adjust switch not pressed -
      ON: Second adjust switch pressed -
      Check Engine SW MIL (Check engine warning light) on request signal / OFF or ON OFF: MIL (Check engine warning light) off -
      ON: MIL (Check engine warning light) on
      Multi Display Select Switch*1 DISP switch (Steering pad switch RH) / OFF or ON OFF: DISP switch not pressed -
      ON: DISP switch pressed
      Drive Monitor Reset SW TRIP switch (Steering pad switch RH) / OFF or ON OFF: DISP switch not pressed -
      ON: DISP switch pressed and holding
      +B Voltage Value Auxiliary battery voltage / Min.: 0 V, Max.: 25.5 V 11 to 14 V -
      Integrated Value for Maintenance*2 Maintenance required reminder value / Min.: 0, Max.: 25500 (mile) Driving distance after performing maintenance required reminder resetting procedure displayed If the value is 5000 (miles) or more, perform the maintenance required reminder resetting procedure after performing maintenance.
      Fuel Input Fuel input / Min.: 0, Max.: 127.5 10th segment comes on:
      39.6 to 45.0      		 Unit: Liter
      9th segment comes on:
      35.9 to 39.6
      8th segment comes on:
      32.0 to 35.9
      7th segment comes on:
      27.8 to 32.0
      6th segment comes on:
      23.6 to 27.8
      5th segment comes on:
      19.4 to 23.6
      4th segment comes on:
      15.3 to 19.4
      3rd segment comes on:
      12.1 to 15.3
      2nd segment comes on:
      8.1 to 12.1
      1st segment comes on:
      5.1 to 8.1
      Rheostat value Light control rheostat value / Min.: 0 (dark), Max.: 100 (bright) Light control rheostat value 0 (dark) The value changes with rheostat operation
      Light control rheostat value 100 (bright)
      TPMS Operation State The condition of the tire pressure / OFF, ON, or Unknown OFF: Tire pressure warning system not operating -
      ON: Tire pressure warning system operating
      Unknown: Wire harness between combination meter sub-assembly and tire pressure warning ECU*4 or tire pressure warning ECU and receiver*5 open
      HV System Indicator Hybrid system indicator value / Min.: - 512, Max.: 511 (%) -512 to 511 (%) -
      Multi Switch (Up)*3 Steering pad switch (Up) / OFF or ON OFF: Steering pad switch (Up) released -
      ON: Steering pad switch (Up) pushed
      Multi Switch (Down)*3 Steering pad switch (Down) / OFF or ON OFF: Steering pad switch (Down) released -
      ON: Steering pad switch (Down) pushed
      Multi Switch (Enter)*3 Steering pad switch (Enter) / OFF or ON OFF: Steering pad switch (Enter) released -
      ON: Steering pad switch (Enter) pushed
      Multi Switch (Right)*3 Steering pad switch (Right) / OFF or ON OFF: Steering pad switch (Right) released -
      ON: Steering pad switch (Right) pushed
      Multi Switch (Left)*3 Steering pad switch (Left) / OFF or ON OFF: Steering pad switch (Left) released -
      ON: Steering pad switch (Left) pushed
      Oil Pressure Switch Oil pressure switch / OFF or ON OFF: Engine started -
      ON: Engine does not start
      Turn Signal Switch (Right) RH turn signal switch / OFF or ON OFF: RH turn signal switch off -
      ON: RH turn signal switch on
      Turn Signal Switch (Left) LH turn signal switch / OFF or ON OFF: LH turn signal switch off -
      ON: LH turn signal switch on
      Hazard Flasher Switch Hazard warning switch / OFF or ON OFF: Hazard warning switch off -
      ON: Hazard warning switch on
      Headlight Auto Leveling Switch*6 Headlight auto leveling switch / OFF or ON OFF: Headlight leveling indicator light off -
      ON: Headlight leveling indicator light on
      Multi Switch (Back)*3 Steering pad switch (Back) / OFF or ON OFF: Steering pad switch (Back) released -
      ON: Steering pad switch (Back) pushed
      Key Remind Sound The pattern of the key reminder warning buzzer / Fast, Normal, Slow Fast, Normal, Slow Displays customize setting of key reminder warning
      Driver Side Seatbelt Warning Buzzer The condition of the seat belt warning buzzer / OFF or ON OFF: The seat belt warning buzzer does not sound at the vehicle speed of 20 km/h (12 mph) or more when the driver seat belt unfastened Displays customize setting of seat belt warning buzzer
      ON: The seat belt warning buzzer sounds at the vehicle speed of 20 km/h (12 mph) or more when the driver seat belt unfastened
      P-Seatbelt Warning Buzzer The condition of the seat belt warning buzzer / OFF or ON OFF: The seat belt warning buzzer does not sound at the vehicle speed of 20 km/h (12 mph) or more when the front passenger seat belt unfastened Displays customize setting of seat belt warning buzzer
      ON: The seat belt warning buzzer sounds at the vehicle speed of 20 km/h (12 mph) or more when the front passenger seat belt unfastened
      Reverse Buzzer The customized setting of the reverse warning buzzer / Continual or Single Continual: When reverse (R) selected, buzzer sounds continuously Displays customize setting of reverse warning buzzer
      Single: When reverse (R) selected, a single buzzer sounds
      ODO Display Time After IG OFF Setting Setting of the ODO display time after the power switch is turned off/30s, 60s, 600s, OFF Displays customize setting of ODO Display Time After IG OFF setting -
      LDA System*3 Existence of function / OFF or ON With: w/ Lane departure alert system -
      Without: w/o Lane departure alert system
      PCS System*3 Existence of function / OFF or ON With: w/ Pre-collision system -
      Without: w/o Pre-collision system
      Radar Cruise System*3 Existence of function / OFF or ON With: w/ Dynamic radar cruise control system -
      Without: w/o Dynamic radar cruise control system
      Number of Trouble Code The number of DTCs which are currently stored / Min.: 0, MAX.: 255 0 -
      • *1: w/o Multi-information display
      • *2: for Speedometer with Imperial units for main scale
      • *3: w/ Multi-information display
      • *4: w/ Vehicle proximity notification system
      • *5: w/o Vehicle proximity notification system
      • *6: w/ Automatic headlight beam level control
      ABS/VSC/TRAC

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Vehicle Speed Vehicle speed / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      ENGINE AND ECT

      Tester Display Measurement Item/Range Normal Condition Stored as Freeze Frame Data
      Diagnostic Note
      Coolant Temp Engine coolant temperature /
      Min.: -40°C (-40°F), Max: 215°C (419°F)      		 75 to 100°C (167 to 212°F): After warming up Yes
      Diagnostic Note:
      This is the engine coolant temperature.
      HINT: 
      • After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
      • After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
      • If the value is -40°C (-40°F) or higher than 135°C (275°F), the sensor circuit may be open or shorted.
      • Check if the engine overheats when the value indicates higher than 135°C (275°F).
      NOTE:

      Enter inspection mode. Refer to INSPECTION MODE PROCEDURE [11/2014 - ] .

      MAIN BODY

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Illumination Rate Info Illumination rate information / 0 ms. to 99.99 ms. Value output according to ambient light level -
  2. ACTIVE TEST 

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Combination Meter / Active Test.
    5. Perform the Active Test according to the display on the Techstream.
      COMBINATION METER

      Tester Display Test Part Control Range Diagnostic Note
      Speed Meter Operation Speedometer 0, 40, 80, 120 mph*1 -
      0, 40, 80, 120, 160 km/h*2
      Fuel Meter Operation Fuel receiver gauge EMPTY, 1/2, FULL -
      A/T Indicator Operation 1 Shift selection indicator light D, P, N, R -
      A/T Indicator Operation 2 Shift selection indicator light B -
      Indicat. Lamp Airbag SRS warning light OFF or ON -
      Indicat. Lamp Doors All Open Open door warning light OFF or ON -
      Driver Side Seat Belt Seat belt warning light OFF or ON -
      Indicat. Lamp ABS ABS warning light OFF or ON -
      Indicat. Lamp Charge Charge warning light OFF or ON -
      Indicat. Lamp Slip Slip indicator light OFF or ON -
      Indicat. Lamp Coolant Hot Engine coolant temperature warning light OFF or ON -
      Indicat. Lamp Beam High beam indicator light OFF or ON -
      Indicat. Lamp Head*1 Head indicator light OFF or ON -
      Indicat. Lamp Tail*2 Tail indicator light OFF or ON -
      Indicat. Lamp Fr FOG*12 Front fog indicator light OFF or ON -
      Indicat. Precrash*3, *9 PCS OFF warning light OFF or ON -
      Driver Side Door Open Open door warning light OFF or ON -
      Front Passenger Side Door Open Open door warning light OFF or ON -
      Indicat. Rear Door RH Open Open door warning light OFF or ON -
      Indicat. Rear Door LH Open Open door warning light OFF or ON -
      Indicat. Lamp Back Door Open Open door warning light OFF or ON -
      Indicat. Headlamp Auto Leveling Headlight leveling warning light OFF or ON -
      Indicat. Lamp Fuel Fuel level warning light OFF or ON -
      Indicat. Tire Pressure Warning System Tire pressure warning light OFF or ON -
      Indicat. Lamp ECB Brake warning light / yellow (minor malfunction) OFF or ON -
      Indicat. Oil Pressure*9 Oil pressure warning light OFF or ON -
      Indicat. ECONO*9 Eco driving indicator light OFF or ON *7
      Indicat. Lamp ECT PWR Power mode indicator light OFF or ON -
      Indicat. Lamp Cruise Cruise control indicator light (green)*4 OFF or ON -
      Cruise control (Constant speed control mode) indicator light (green)*5
      Indicat. Lamp Brake Brake warning light / red (malfunction) OFF or ON -
      Indicat. EPS EPS warning light OFF or ON -
      Indicat. KEY*9 Smart key warning light OFF or ON -
      Indicat. Oil Maintenance*1, *9 Maintenance required reminder indicator light OFF or ON -
      Indicat. Ready (HV) Ready indicator light OFF or ON -
      Indicat. EV Mode EV mode indicator light OFF or ON -
      Indicat. SET Cruise control SET indicator light OFF or ON -
      HV System Warning HV system warning light OFF or ON -
      Indicat. Radar Cruise*5 Cruise control indicator light (Vehicle-to-vehicle distance control mode) (green) OFF or ON -
      Indicat. ECO MODE Eco mode indicator light OFF or ON -
      Cruise Indicator*9 Cruise control indicator light (amber) OFF or ON -
      Radar Cruise Indicator*5 Cruise control indicator light (Vehicle-to-vehicle distance control mode) (amber) OFF or ON -
      Shift-by-wire Warning*9 Parking lock system warning light and parking lock system warning message OFF or ON -
      P Range Indicator*9 P position request indicator light OFF or ON -
      EV Mode Indicator*9 EV indicator light OFF or ON *7
      HV Unit Hot Warning Indicator*9 Hybrid system overheat warning light OFF or ON -
      HV System Certification Mode Indicator*9 HV system warning light OFF or ON -
      LED Head Lamp Warning*6, *9 LED headlight warning light OFF or ON -
      Turn Signal (Left) Indicator LH Turn indicator light OFF or ON -
      Turn Signal (Right) Indicator RH Turn indicator light OFF or ON -
      Indicat. VSC OFF VSC OFF indicator light OFF or ON -
      Go to Service Warning*9 Go to service warning light OFF or ON -
      VSC TRC Indicator TRAC OFF indicator light OFF or ON -
      Master Warning*8 Master warning light OFF or ON -
      LDA Control Indicator*10 Lane departure alert indicator light OFF or ON -
      Automatic High Beam Indicator*11 Automatic high beam indicator light OFF or ON -
      HV System Indicator Hybrid system indicator MIN, -50, 0, 100, 200, 300, 400, MAX *7
      Meter Display 1 Multi-information display*8 / Segment display 0, 1, 2, 3, 4, 5, 6, All *13
      Meter Display 2*9 Segment display 7, 8, 9 -
      • *1: for Speedometer with Imperial units for main scale
      • *2: for Speedometer with Metric units for main scale
      • *3: w/ Pre-collision system
      • *4: w/o Dynamic radar cruise control system
      • *5: w/ Dynamic radar cruise control system
      • *6: w/ LED headlights
      • *7: Indicator or warning light does not operate when the mode has been disabled via customization function.
      • *8: w/ Multi-information display
      • *9: w/o Multi-information display
      • *10: w/ Lane departure alert system
      • *11: w/ Automatic high beam system
      • *12: w/ Front fog light
      • *13: The multi-information display operates only when All is selected.
scientia non olet · About LEMON Manuals