Typical Enabling Conditions

WARNING: This page is about a different car, the 2019 Toyota Highlander, 2018 Toyota Highlander, and 2017 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.

ALL

The monitor will run whenever the following DTCs are not stored	P0717, P07BF, P07C0 (Turbine speed sensor circuit) P0793, P07C5, P07C6 (Intermediate shaft speed sensor circuit) P0712, P0713 (ATF temperature sensor circuit (TFT sensor)) P0962, P0963 (Solenoid (SL1) valve circuit) P0966, P0967 (Solenoid (SL2) valve circuit) P0970, P0971 (Solenoid (SL3) valve circuit) P2814, P2815 (Solenoid (SL4) valve circuit) P281D, P281E (Solenoid (SL5) valve circuit) P08C1, P08C2 (Solenoid (SL6) valve circuit) P2769, P2770 (Solenoid (SL) valve circuit) P2764, P2763 (Solenoid (SLU) valve circuit) P2720, P2721 (Solenoid (SLT) valve circuit) P0117, P0118 (ECT sensor circuit) P0335, P0337, P0338 (Crankshaft Position Sensor circuit) P0327, P0328, P0332, P0333 (KCS sensor circuit) P0121, P0122, P0123, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P061E, P0657, P0658, P2102, P2103, P2111, P2112, P2119, P2135 ((ETCS) Electronic throttle control system) U0100 (CAN communication system)
Shift position	"D", "not R" and "not N"
Elapsed time since shift lever moved from "N" to "D"	4 sec. or more
ATF temperature	-10°C (14°F) or more
Engine	Starting

ON malfunction (A)

START CONDITIONS OF J1SUMMAX CALCULATION

Turbine speed	900 rpm or more
Neutral state under low torque flag	OFF
ECM selected gear	1st
Time after transition to 1st gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
Turbine speed - Output speed x 1st gear ratio	150 rpm or more
Output speed	More than 0 rpm
Calculated input torque when the following conditions are met: (a), (b) and (c)	Specified value
(a) ECM selected gear	1st
(b) Time after transition to 1st gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
(c) Turbine speed - Output speed x 1st gear ratio	150 rpm or more

FINISH CONDITIONS OF J1SUMMAX CALCULATION

Any of the following conditions are met: (a), (b), (c), (d), (e) or (f)	-
(a) Turbine speed	Less than 900 rpm
(b) Neutral state under low torque flag	ON
(c) ECM selected gear	Not 1st
(d) Duration time while following condition met	0 sec. or more
Turbine speed - Output speed x 1st gear ratio	Less than 50 rpm
(e) Pass condition met	-
(f) ECM selected gear	Neutral

ON malfunction (B)

START CONDITIONS OF J2SUMMAX CALCULATION

Turbine speed	900 rpm or more
Neutral state under low torque flag	OFF
ECM selected gear	2nd
Time after transition to 2nd gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
Turbine speed - Output speed x 2nd gear ratio	150 rpm or more
Output speed	More than 0 rpm
Calculated input torque when the following conditions are met: (a), (b) and (c)	Specified value
(a) ECM selected gear	2nd
(b) Time after transition to 2nd gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
(c) Turbine speed - Output speed x 2nd gear ratio	150 rpm or more

FINISH CONDITIONS OF J2SUMMAX CALCULATION

Any of the following conditions are met: (a), (b), (c), (d), (e) or (f)	-
(a) Turbine speed	Less than 900 rpm
(b) Neutral state under low torque flag	ON
(c) ECM selected gear	Not 2nd
(d) Duration time while following condition met	0 sec. or more
Turbine speed - Output speed x 2nd gear ratio	Less than 50 rpm
(e) Pass condition met	-
(f) ECM selected gear	Neutral

ON malfunction (C)

START CONDITIONS OF J3SUMMAX CALCULATION

Turbine speed	900 rpm or more
Neutral state under low torque flag	OFF
ECM selected gear	3rd
Time after transition to 3rd gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
Turbine speed - Output speed x 3rd gear ratio	150 rpm or more
Output speed	More than 0 rpm
Calculated input torque when the following conditions are met: (a), (b) and (c)	Specified value
(a) ECM selected gear	3rd
(b) Time after transition to 3rd gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
(c) Turbine speed - Output speed x 3rd gear ratio	150 rpm or more

FINISH CONDITIONS OF J3SUMMAX CALCULATION

Any of the following conditions are met: (a), (b), (c), (d), (e) or (f)	-
(a) Turbine speed	Less than 900 rpm
(b) Neutral state under low torque flag	ON
(c) ECM selected gear	Not 3rd
(d) Duration time while following condition met	0 sec. or more
Turbine speed - Output speed x 3rd gear ratio	Less than 50 rpm
(e) Pass condition met	-
(f) ECM selected gear	Neutral

ON malfunction (D)

START CONDITIONS OF J4SUMMAX CALCULATION

Turbine speed	900 rpm or more
Neutral state under low torque flag	OFF
ECM selected gear	4th
Time after transition to 4th gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
Turbine speed - Output speed x 4th gear ratio	150 rpm or more
Output speed	More than 0 rpm
Calculated input torque when the following conditions are met: (a), (b) and (c)	Specified value
(a) ECM selected gear	4th
(b) Time after transition to 4th gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
(c) Turbine speed - Output speed x 4th gear ratio	150 rpm or more

FINISH CONDITIONS OF J4SUMMAX CALCULATION

Any of the following conditions are met: (a), (b), (c), (d), (e) or (f)	-
(a) Turbine speed	Less than 900 rpm
(b) Neutral state under low torque flag	ON
(c) ECM selected gear	Not 4th
(d) Duration time while following condition met	0 sec. or more
Turbine speed - Output speed x 4th gear ratio	Less than 50 rpm
(e) Pass condition met	-
(f) ECM selected gear	Neutral

ON malfunction (E)

START CONDITIONS OF J5SUMMAX CALCULATION

Turbine speed	900 rpm or more
Neutral state under low torque flag	OFF
ECM selected gear	5th
Time after transition to 5th gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
Turbine speed - Output speed x 5th gear ratio	150 rpm or more
Output speed	More than 0 rpm
Calculated input torque when the following conditions are met: (a), (b) and (c)	Specified value
(a) ECM selected gear	5th
(b) Time after transition to 5th gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
(c) Turbine speed - Output speed x 5th gear ratio	150 rpm or more

FINISH CONDITIONS OF J5SUMMAX CALCULATION

Any of the following conditions are met: (a), (b), (c), (d), (e) or (f)	-
(a) Turbine speed	Less than 900 rpm
(b) Neutral state under low torque flag	ON
(c) ECM selected gear	Not 5th
(d) Duration time while following condition met	0 sec. or more
Turbine speed - Output speed x 5th gear ratio	Less than 50 rpm
(e) Pass condition met	-
(f) ECM selected gear	Neutral

ON malfunction (F)

START CONDITIONS OF J6SUMMAX CALCULATION

Turbine speed	900 rpm or more
Neutral state under low torque flag	OFF
ECM selected gear	6th
Time after transition to 6th gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
Turbine speed - Output speed x 6th gear ratio	150 rpm or more
Output speed	More than 0 rpm
Calculated input torque when the following conditions are met: (a), (b) and (c)	Specified value
(a) ECM selected gear	6th
(b) Time after transition to 6th gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
(c) Turbine speed - Output speed x 6th gear ratio	150 rpm or more

FINISH CONDITIONS OF J6SUMMAX CALCULATION

Any of the following conditions are met: (a), (b), (c), (d), (e) or (f)	-
(a) Turbine speed	Less than 900 rpm
(b) Neutral state under low torque flag	ON
(c) ECM selected gear	Not 6th
(d) Duration time while following condition met	0 sec. or more
Turbine speed - Output speed x 6th gear ratio	Less than 50 rpm
(e) Pass condition met	-
(f) ECM selected gear	Neutral

ON malfunction (G)

START CONDITIONS OF J7SUMMAX CALCULATION

Turbine speed	900 rpm or more
Neutral state under low torque flag	OFF
ECM selected gear	7th
Time after transition to 7th gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
Turbine speed - Output speed x 7th gear ratio	150 rpm or more
Output speed	More than 0 rpm
Calculated input torque when the following conditions are met: (a), (b) and (c)	Specified value
(a) ECM selected gear	7th
(b) Time after transition to 7th gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
(c) Turbine speed - Output speed x 7th gear ratio	150 rpm or more

FINISH CONDITIONS OF J7SUMMAX CALCULATION

Any of the following conditions are met: (a), (b), (c), (d), (e) or (f)	-
(a) Turbine speed	Less than 900 rpm
(b) Neutral state under low torque flag	ON
(c) ECM selected gear	Not 7th
(d) Duration time while following condition met	0 sec. or more
Turbine speed - Output speed x 7th gear ratio	Less than 50 rpm
(e) Pass condition met	-
(f) ECM selected gear	Neutral

ON malfunction (H)

START CONDITIONS OF J8SUMMAX CALCULATION

Turbine speed	900 rpm or more
Neutral state under low torque flag	OFF
ECM selected gear	8th
Time after transition to 8th gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
Turbine speed - Output speed x 8th gear ratio	150 rpm or more
Output speed	More than 0 rpm
Calculated input torque when the following conditions are met: (a), (b) and (c)	Specified value
(a) ECM selected gear	8th
(b) Time after transition to 8th gear	-
- when detected abnormal shift	1.5 sec. or more
- when not detected abnormal shift	Immediately after approval
(c) Turbine speed - Output speed x 8th gear ratio	150 rpm or more

FINISH CONDITIONS OF J8SUMMAX CALCULATION

Any of the following conditions are met: (a), (b), (c), (d), (e) or (f)	-
(a) Turbine speed	Less than 900 rpm
(b) Neutral state under low torque flag	ON
(c) ECM selected gear	Not 8th
(d) Duration time while following condition met	0 sec. or more
Turbine speed - Output speed x 8th gear ratio	Less than 50 rpm
(e) Pass condition met	-
(f) ECM selected gear	Neutral

ON malfunction (J)

ECM selected gear 4th

ON malfunction (K) and (L)

ECM selected gear 8th

ON malfunction (N)

Fail-safe mode flag	OFF
ECM selected gear	3rd
ON malfunction condition (Q)	Fixed

ON malfunction (O)

Fail-safe mode flag	OFF
ECM selected gear	5th
ON malfunction condition (R)	Fixed

ON malfunction (P)

Fail-safe mode flag	OFF
ECM selected gear	4th
ON malfunction condition (S)	Fixed

ON malfunction (Q)

ECM selected gear	1st or 2nd
Neutral state flag	ON
Calculated input torque when Neutral state flag ON	Specified value
1st gear pass detection	Not fixed (after transition to latest gear)
2nd gear pass detection	Not fixed (after transition to latest gear)
Output speed x 3rd gear ratio	Less than 6500 rpm

ON malfunction (R)

ECM selected gear	3rd, 4th, 6th, 7th or 8th
Neutral state flag	ON
Calculated input torque when Neutral state flag ON	Specified value
Output speed x 5th gear ratio	Less than 6500 rpm

Any of the following conditions are met: condition (a) or (b)

CONDITION (A)

ECM selected gear	8th
8th gear pass detection	Not fixed (after transition to latest gear)

CONDITION (B)

Following conditions are met	(1) and (((2), (3), (4) and (5)) or (6))
(1) ECM selected gear	3rd, 4th, 6th or 7th
(2) 3rd gear pass detection	Not fixed (after transition to latest gear)
(3) 4th gear pass detection	Not fixed (after transition to latest gear)
(4) 6th gear pass detection	Not fixed (after transition to latest gear)
(5) 7th gear pass detection	Not fixed (after transition to latest gear)
(6) ECM commanded solenoid (SL) valve state	OFF (after transition to latest gear)

Any of the following conditions are met: condition (a), (b), (c) or (d)

CONDITION (A)

ECM selected gear	4th or 7th
Turbine speed - Output speed x 3rd gear ratio	More than 50 rpm

CONDITION (B)

ECM selected gear	6th
Turbine speed - Output speed x 4th gear ratio	More than 50 rpm

CONDITION (C)

ECM selected gear	8th
Turbine speed - Output speed x 5th gear ratio	More than 50 rpm

CONDITION (D)

ECM selected gear

3rd

ON malfunction (S)

ECM selected gear	5th
Neutral state flag	ON
Calculated input torque when Neutral state flag ON	Specified value
5th gear pass detection	Not fixed (after transition to latest gear)
Turbine speed - Output speed x 3rd gear ratio	More than 50 rpm
Output speed x 4th gear ratio	Less than 6500 rpm

OFF malfunction

Fail-safe function does not operate due to the following malfunctions:	-
Solenoid (SL1) valve	Not OFF or ON malfunction (P0746)
Solenoid (SL2) valve	Not OFF or ON malfunction (P0776)
Solenoid (SL3) valve	Not OFF or ON malfunction (P0796)
Solenoid (SL4) valve	Not OFF or ON malfunction (P2808)
Solenoid (SL5) valve	Not OFF or ON malfunction (P2817)
Solenoid (SL6) valve	Not OFF or ON malfunction (P08BB)
Solenoid (SLT) valve	Not OFF malfunction (P2714)
Solenoid (SLU) valve	Not ON malfunction (P2757)
Solenoid (SL) valve	Not ON malfunction (P0741)
All shift solenoids	Not being stopped
Neutral command flag	Not met
ECM selected gear	2nd, 3rd, 4th, 6th, 7th or 8th
Vehicle speed	2 km/h (1.2 mph) or more
Throttle valve opening angle	5% or more at engine speed 2000 rpm (conditions vary with engine speed)
Calculated load value	-
- When A/C off	16.0% or more
- When A/C on	19.0% or more
ECT	40°C (104°F) or more
Spark advance from MAX. retard timing by KCS control	0 °CA or more

HINT:

NEUTRAL STATE UNDER LOW TORQUE FLAG

Neutral state flag	ON
ECM selected gear	1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th
Fail-safe mode flag	OFF

Any of the following conditions are met: Condition (a) or (b)

CONDITION (A)

ECM selected gear	1st, 2nd, 5th or 8th
1st gear pass detection	Not fixed (after transition to latest gear)
2nd gear pass detection	Not fixed (after transition to latest gear)
5th gear pass detection	Not fixed (after transition to latest gear)
8th gear pass detection	Not fixed (after transition to latest gear)

CONDITION (B)

Following conditions are met	(1) and (((2), (3), (4) and (5)) or (6))
(1) ECM selected gear	3rd, 4th, 6th or 7th
(2) 3rd gear pass detection	Not fixed (after transition to latest gear)
(3) 4th gear pass detection	Not fixed (after transition to latest gear)
(4) 6th gear pass detection	Not fixed (after transition to latest gear)
(5) 7th gear pass detection	Not fixed (after transition to latest gear)
(6) ECM commanded solenoid (SL) valve state	OFF (after transition to latest gear)

Any of the following conditions are met: Condition (a), (b), (c) or (d)

CONDITION (A)

ECM selected gear	4th, 5th or 7th
Turbine speed - Output speed x 3rd gear ratio	More than 50 rpm

CONDITION (B)

ECM selected gear	6th
Turbine speed - Output speed x 4th gear ratio	More than 50 rpm

CONDITION (C)

ECM selected gear	8th
Turbine speed - Output speed x 5th gear ratio	More than 50 rpm

CONDITION (D)

ECM selected gear

1st, 2nd or 3rd

NEUTRAL STATE FLAG:

Turbine speed - output speed x (ECM selected gear)

1000 rpm or more

NEUTRAL COMMAND FLAG:

Engine speed	7200 rpm or more
Turbine speed	7200 rpm or more

Any of the following conditions are met: Condition (a) or (b)

Condition (a)

ECM selected gear	6th or 7th or 8th
Output speed x 5th gear ratio	7200 rpm or more

Condition (b)

ECM selected gear	4th or 5th
Output speed x 3rd gear ratio	7200 rpm or more