LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2015 >> Highlander LE Plus, FWD >> Repair and Diagnosis >> Electrical >> Gauges >> Meter / Gauge / Display - Diagnostics Codes - Symptom & Circuit Tests - (Except Hybrid) >> Meter / Gauge System >> On-Vehicle Inspection [12/2013 - 11/2016] >> Procedure

On-Vehicle Inspection [12/2013 - 11/2016]: Procedure

  1. INSPECT COMBINATION METER ASSEMBLY 
    1. Check speedometer operation
      NOTE:
      • The combination meter assembly receives the vehicle speed signal from the brake actuator assembly (skid control ECU) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the brake actuator assembly (skid control ECU) because it is the source of the vehicle speed signal.
      • Data List values of the brake actuator assembly (skid control ECU) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.
      • If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
      1. Warm up the engine.
      2. Connect the Techstream to the DLC3.
      3. Turn the ignition switch to ON.
      4. Turn the Techstream on.
      5. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
      6. Check the values by referring to the table below.

        Chassis > ABS/VSC/TRAC > Data List 

        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations

        Chassis > ABS/VSC/TRAC > Data List 

        Tester Display
        Vehicle Speed
        REFERENCE KM/H

        Techstream Indication (km/h) Acceptable Range (km/h)
        20 18.5 to 22.5
        40 38.9 to 43.4
        60 59.4 to 63.9
        80 79.7 to 84.7
        100 100.2 to 105.2
        120 120.8 to 125.8
        140 141.3 to 146.3
        160 161.9 to 166.9
        180 182.4 to 187.4
        200 203.0 to 208.0
        REFERENCE MPH

        Techstream Indication (mph) Acceptable Range (mph)
        20 19.3 to 21.8
        40 39.7 to 42.5
        60 60.2 to 63.0
        80 80.6 to 83.8
        100 101.1 to 104.3
        120 121.7 to 124.9

        OK

        Speedometer reading is within the acceptable range at each vehicle speed.

      7. Check the deflection width of the speedometer indicator.

        Reference

        Within 0.3°

    2. Inspect tachometer
      1. Warm up the engine.
      2. Connect the Techstream to the DLC3.
      3. Turn the ignition switch to ON.
      4. Turn the Techstream on.
      5. Enter the following menus: Powertrain / Engine / Data List.
      6. Check the values by referring to the table below.

        Powertrain > Engine > Data List 

        Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
        Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm 610 to 710 rpm: Idling for 1AR-FE:
        Idling (engine warmed up and A/C off): 660 rpm
        for 2GR-FE:
        Idling (engine warmed up and A/C off): 667 rpm        		 When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.

        Powertrain > Engine > Data List 

        Tester Display
        Engine Speed
        REFERENCE

        Techstream Indication (rpm) Acceptable Range (rpm)
        Data in () is for Reference
        700 630 to 770
        1000 (900 to 1100)
        2000 (1850 to 2150)
        3000 2800 to 3200
        4000 (3800 to 4200)
        5000 4800 to 5200
        6000 (5750 to 6250)
        7000 6700 to 7300

        OK

        Tachometer reading is within the acceptable range at each engine speed.

      7. Check the deflection width of the tachometer indicator.

        Reference

        Within 0.3°

    3. Check LED illumination (LED check)
      1. Check the illumination function of the warning or indicator lights listed below when turning the ignition switch to ON.

        OK

        Warning or Indicator Light Specified Condition
        Brake warning light Warning or indicator light comes on for about 3 seconds after turning the ignition switch to ON.
        VSC OFF indicator light
        Slip indicator light
        ABS warning light
        Tire pressure warning light*1
        PCS warning light*2
        Downhill assist control indicator light*3
        Eco driving indicator light
        Master warning light
        AWD lock indicator light*3 Warning light comes on for about 4 seconds after turning the ignition switch to ON.
        SRS warning light Warning light comes on for about 6 seconds after turning the ignition switch to ON.
        Charge warning light*4 Warning light comes on when turning the ignition switch to ON.
        MIL (Check engine warning light)
        EPS warning light
        Engine oil pressure warning light*4
        • *1: w/ Tire Pressure Warning System
        • *2: w/ Pre-collision System
        • *3: for AWD
        • *4: for Multi-information Display (Monochrome Type)
scientia non olet · About LEMON Manuals