LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2015 >> Highlander LE Plus, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 25 (SFI System [1AR-FE] - Diagnostic Codes - (Except Hybrid) (2 Of 8)) >> SFI System >> DTC P0365: Camshaft Position Sensor "B" Circuit (Bank 1); DTC P0367: Camshaft Position Sensor "B" Circuit Low Input (Bank 1); DTC P0368: Camshaft Position Sensor "B" Circuit High Input (Bank 1) [11/2016 - 10/2017] >> Procedure

DTC P0365: Camshaft Position Sensor "B" Circuit (Bank 1); DTC P0367: Camshaft Position Sensor "B" Circuit Low Input (Bank 1); DTC P0368: Camshaft Position Sensor "B" Circuit High Input (Bank 1) [11/2016 - 10/2017]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)) 
    GTY443550Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Front view of wire harness connector
    (to Camshaft Position Sensor (for Exhaust Camshaft))
    1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.
    2. Turn the ignition switch to ON.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      C20-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.5 V

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    See step  10

    Result:  1

    OK 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM) 
    1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.
    2. Disconnect the ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C20-1 (VVE+) - C1-81 (EV1+) Always Below 1 Ω
      C20-2 (VVE-) - C1-112 (EV1-) Always Below 1 Ω
      C20-1 (VVE+) or C1-81 (EV1+) - Body ground Always 10 kΩ or higher
      C20-2 (VVE-) or C1-112 (EV1-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result:  1

    OK 

    See step  3

  3. CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)) 
    GTY437032Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Clearance
    1. Check the camshaft position sensor (for exhaust camshaft) installation.

      OK

      Camshaft position sensor (for exhaust camshaft) is installed correctly.

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    SECURELY REINSTALL CAMSHAFT POSITION SENSOR (for EXHAUST CAMSHAFT). Refer to  INSTALLATION [11/2015 - ] 

    Result:  1

    OK 

    See step  4

  4. INSPECT EXHAUST CAMSHAFT (TIMING ROTOR) 
    1. Inspect the timing rotor of the exhaust camshaft.

      OK

      Camshaft timing rotor does not have any cracks or deformation.

      HINT: 

      Perform "Inspection After Repair" after replacing the exhaust camshaft.

      Refer to INITIALIZATION [12/2013 - ]

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPLACE EXHAUST CAMSHAFT. Refer to  REMOVAL [11/2016 - ] 

    Result:  1

    OK 

    See step  5

  5. CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) 

    Refer to PROCEDURE - Step 5

    Result

    Proceed to
    OK
    NG

    Result:  2

    NG 

    See step  8

    Result:  1

    OK 

    See step  6

  6. REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) 
    1. Replace the camshaft position sensor (for exhaust camshaft).

      Refer to REMOVAL [12/2013 - ]

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  7

  7. CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [11/2016 - ]

      Powertrain > Engine and ECT > Clear DTCs 

    5. Turn the ignition switch off and wait for at least 30 seconds.
    6. Start the engine.
    7. Turn the Techstream on.
    8. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
    10. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes 

      Result

      Result Proceed to
      DTCs are not output A
      DTC P0365, P0367 or P0368 is output B

      HINT: 

      If the engine does not start, replace the ECM.

    Result:  1

    A 

    END 

    Result:  2

    B 

    REPLACE ECM. Refer to  REMOVAL [12/2013 - ] 

  8. CHECK ENGINE MECHANICAL SYSTEM 
    1. Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA 

    Result:  1

    OK 

    See step  9

  9. CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [11/2016 - ]

      Powertrain > Engine and ECT > Clear DTCs 

    5. Turn the ignition switch off and wait for at least 30 seconds.
    6. Start the engine.
    7. Turn the Techstream on.
    8. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
    10. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes 

      Result

      Result Proceed to
      DTCs are not output A
      DTC P0365, P0367 or P0368 is output B

    Result:  1

    A 

    CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS [12/2013 - ] 

    Result:  2

    B 

    REPLACE ECM. Refer to  REMOVAL [12/2013 - ] 

  10. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM) 
    1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.
    2. Disconnect the ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C20-3 (VC2) - C1-111 (VCE1) Always Below 1 Ω
      C20-3 (VC2) or C1-111 (VCE1) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result:  1

    OK 

    REPLACE ECM. Refer to  REMOVAL [12/2013 - ] 

    Result:  2

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals