LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2015 >> Highlander LE Plus, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 63 (SFI System (2GR-FXS) - Diagnostic Codes - (Hybrid) (3 Of 4)) >> SFI System >> DTC P0011: Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1); DTC P0012: Camshaft Position "A" - Timing Over-Retarded (Bank 1); DTC P0021: Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2); DTC P0022: Camshaft Position "A" - Timing Over-Retarded (Bank 2) [11/2016 - ] >> Confirmation Driving Pattern

Confirmation Driving Pattern

WARNING: This page is about a different car, the 2019 Toyota Highlander, 2018 Toyota Highlander, and 2017 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
GTY617837Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

    HINT: 

    • P0011 or P0021 was output:

      Clear the DTC without using the Techstream.

    • P0012 or P0022 was output:

      Clear the DTC using the Techstream.

  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the Techstream on [A].
  6. Put the engine in INSPECTION MODE PROCEDURE (maintenance mode).
  7. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  8. With the engine running, accelerate the vehicle to 75 km/h (46 mph) or more by depressing the accelerator pedal for 10 seconds or more [C].
    WARNING:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT: 

    If the engine stops, further depress the accelerator pedal to restart the engine.

  9. Idle the engine for 100 seconds or more [D].
  10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  11. Read the pending DTCs.

    HINT: 

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  13. Input the DTC: P0011, P0012, P0021 or P0022.
  14. Check the DTC judgment result.
    Techstream Display Description
    NORMAL
    • DTC judgment completed
    • System normal
    ABNORMAL
    • DTC judgment completed
    • System abnormal
    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions
    N/A
    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT: 

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].
  15. With the engine running, accelerate the vehicle to 75 km/h (46 mph) or more by depressing the accelerator pedal for 10 seconds or more [F].
    WARNING:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT: 

    If the engine stops, further depress the accelerator pedal to restart the engine.

  16. Idle the engine for 100 seconds or more [G].
  17. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].
  18. Read the pending DTCs.

    HINT: 

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  19. Check the DTC judgment result again.

    HINT: 

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform the following procedure.
  20. Perform a universal trip and check for permanent DTCs.

    Refer to DTC CHECK / CLEAR [11/2016 - ]

    HINT: 

    • If a permanent DTC is output, the system is malfunctioning.
    • If no permanent DTC is output, the system is normal.
scientia non olet · About LEMON Manuals