Problem Symptoms Table [12/2013 - 11/2016]
NOTE:
If the main body ECU (multiplex network body ECU) is replaced, refer to Registration.*1
Refer to REGISTRATION [12/2013 - 11/2016] .
- *1: w/ Smart Key System
HINT:
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptom are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
METER OR GAUGE
| Symptom | Suspected Area | Link |
|---|---|---|
| Entire combination meter assembly does not operate | Power source circuit | Refer to Entire Combination Meter does not Operate [12/2013 - 11/2016] |
| Speedometer malfunction | Speedometer circuit | Refer to Speedometer Malfunction [12/2013 - ] |
| Tachometer malfunction | Tachometer circuit | Refer to Tachometer Malfunction [12/2013 - 11/2016] |
| Fuel receiver gauge display malfunction (Fuel receiver gauge is currently malfunctioning, or was malfunctioning in the past) | Fuel receiver gauge display circuit | Refer to Fuel Receiver Gauge Display Malfunction [12/2013 - 11/2016] |
| Engine coolant temperature receiver gauge malfunction | Engine coolant temperature receiver gauge circuit | Refer to Engine Coolant Temperature Receiver Gauge Malfunction [12/2013 - 11/2016] |
WARNING OR INDICATOR
| Symptom | Suspected Area | Link |
|---|---|---|
| Master warning light malfunction | Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Master Warning) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Door open warning light malfunction (Each door courtesy switch or glass hatch courtesy switch operation is normal)*1 | Combination meter assembly (LED): Perform Active Test (Indicat. Lamp Doors All Open) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| Brake warning light malfunction | Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Indicat. Lamp Brake) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| Brake warning light circuit (Brake warning light remains ON) | Refer to Brake Warning Light Remains ON [12/2013 - 11/2016] | |
| Brake warning light circuit (Brake warning light does not come ON) | Refer to Brake Warning Light does not Come ON [12/2013 - ] | |
| Brake master cylinder reservoir sub-assembly (Brake fluid level warning switch) | Refer to REMOVAL [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| Brake actuator assembly (Skid control ECU) | Refer to REMOVAL [12/2013 - 11/2016] | |
| Driver or front passenger seat belt warning light malfunction | Combination meter assembly (LED): Perform Active Test (Driver Side Seat Belt) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Driver seat belt warning light circuit | Refer to Driver Side Seat Belt Warning Light does not Operate [12/2013 - ] | |
| Front passenger seat belt warning light circuit | Refer to Front Passenger Side Seat Belt Warning Light Malfunction [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| Airbag sensor assembly | Refer to REMOVAL [12/2013 - ] | |
| SRS warning light malfunction | Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Indicat. Lamp Airbag) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| SRS warning light circuit (SRS warning light remains ON) | Refer to SRS Warning Light Remains ON [12/2013 - 11/2016] | |
| SRS warning light circuit (SRS warning light does not come ON) | Refer to SRS Warning Light does not Come ON [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Airbag sensor assembly | Refer to REMOVAL [12/2013 - ] | |
| Charge warning light malfunction*1 | Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Indicat. Lamp Charge) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Charging system (for 1AR-FE) | Refer to PROBLEM SYMPTOMS TABLE [12/2013 - ] | |
| Charging system (for 2GR-FE) | Refer to PROBLEM SYMPTOMS TABLE [12/2013 - 11/2016] | |
| Generator assembly (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| Generator assembly (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| Wire harness or connector (Combination meter assembly - Generator assembly) | - | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| Engine oil pressure warning light malfunction*1 | Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Indicat. Oil Pressure) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| Engine oil pressure switch assembly (for 1AR-FE) | Refer to INSPECTION [12/2013 - ] | |
| Engine oil pressure switch assembly (for 2GR-FE) | Refer to INSPECTION [12/2013 - 11/2016] | |
| Wire harness or connector (Combination meter assembly - Engine oil pressure switch assembly) | - | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| EPS warning light malfunction | Combination meter assembly (LED): LED check | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Indicat. EPS) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| EPS warning light circuit | Refer to EPS Warning Light Circuit [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| MIL (Check engine warning light) malfunction | Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Check Engine Indicator) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| MIL circuit (for 1AR-FE) | Refer to MIL Circuit [12/2013 - 11/2016] | |
| MIL circuit (for 2GR-FE) | Refer to MIL Circuit [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| PCS warning light malfunction*3 | Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Indicat. Precrash) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| Slip indicator light malfunction | Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Indicat. Lamp Slip) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| Slip indicator light circuit (Slip indicator light remains ON) | Refer to Slip Indicator Light Remains ON [12/2013 - 11/2016] | |
| Slip indicator light circuit (Slip indicator light does not come ON) | Refer to Slip Indicator Light does not Come ON [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Brake actuator assembly (Skid control ECU) | Refer to REMOVAL [12/2013 - 11/2016] | |
| VSC OFF indicator light malfunction | Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Indicat. VSC OFF) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| VSC OFF indicator light circuit (VSC OFF switch circuit) | Refer to VSC OFF Switch Circuit [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Brake actuator assembly (Skid control ECU) | Refer to REMOVAL [12/2013 - 11/2016] | |
| ABS warning light malfunction | Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Indicat. Lamp ABS) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| ABS warning light circuit (ABS warning light remains ON) | Refer to ABS Warning Light Remains ON [12/2013 - 11/2016] | |
| ABS warning light circuit (ABS warning light does not come ON) | Refer to ABS Warning Light does not Come ON [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Brake actuator assembly (Skid control ECU) | Refer to REMOVAL [12/2013 - 11/2016] | |
| Tire pressure warning light malfunction*4 | Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Indicat. Tire Pressure Warning System) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| Tire pressure warning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| Fuel level warning light malfunction | Combination meter assembly (LED): Perform Active Test (Indicat. Lamp Fuel) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Fuel sender gauge assembly (for 1AR-FE) | Refer to INSPECTION [12/2013 - ] | |
| Fuel sender gauge assembly (for 2GR-FE) | Refer to INSPECTION [12/2013 - 11/2016] | |
| Wire harness or connector (Combination meter assembly - Fuel sender gauge assembly) | - | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| SNOW indicator display malfunction*1 | Automatic transaxle system (for U660E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Automatic transaxle system (for U660F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Automatic transaxle system (for U760E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| AWD lock indicator light malfunction*5 | Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Indicat. 4WD Lock) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| Automatic high beam indicator light malfunction*6 | Combination meter assembly (LED): Perform Active Test (Automatic High Beam Indicator) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Automatic high beam system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| Lane departure alert indicator light malfunction*1, *7 | Combination meter assembly (LED): Perform Active Test (LDA Control Indicator) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Lane departure alert indicator light circuit (Indicator circuit) | Refer to Indicator Circuit [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| Cruise control indicator light malfunction*1 | Combination meter assembly (LED): Perform Active Test (Indicat. Lamp Cruise) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Cruise control indicator light circuit (Cruise main indicator light circuit) | Refer to Cruise Main Indicator Light Circuit [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| High beam indicator light malfunction (High beam head light is normal) | Combination meter assembly (LED): Perform Active Test (Indicat. Lamp Beam) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| Downhill assist control indicator light malfunction*5 | Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] |
| Combination meter assembly (LED): Perform Active Test (Indicat. Downhill Assist Control) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| Downhill assist control indicator light (Downhill assist control indicator light remains ON) | Refer to Downhill Assist Control Indicator Light Remains ON [12/2013 - 11/2016] | |
| Downhill assist control indicator light (Downhill assist control indicator light does not come ON) | Refer to Downhill Assist Control Indicator Light does not Come ON [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Brake actuator assembly (Skid control ECU) | Refer to REMOVAL [12/2013 - 11/2016] | |
| Tail indicator light malfunction (Taillight is normal)*8 | Combination meter assembly (LED): Perform Active Test (Indicat. Lamp Tail) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| Head indicator light malfunction (Low beam head light is normal)*9 | Combination meter assembly (LED): Perform Active Test (Indicat. Lamp Head) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| Front fog indicator light malfunction (Front fog light is normal)*10 | Combination meter assembly (LED): Perform Active Test (Indicat. Lamp Fr FOG) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| Turn indicator light malfunction (Turn signal light operation is normal) | Check customize parameters (Lane Change Flashing Times Setting) | Refer to CUSTOMIZE PARAMETERS [12/2013 - ] |
| Combination meter assembly (LED): Perform Active Test (Turn Signal (Left) Indicator, Turn Signal (Right) Indicator) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| DCM (Telematics transceiver) (w/ Manual (SOS) Switch) | Refer to REMOVAL [12/2013 - 11/2016] | |
| Multiplex network door ECU (w/ Power Back Door System) | Refer to REMOVAL [12/2013 - ] | |
| Eco driving indicator light malfunction | Check customize parameters (ECO driving indicator light) | - |
| Combination meter assembly (LED): LED check | Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016] | |
| Combination meter assembly (LED): Perform Active Test (Indicat. ECONO) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| Cruise control SET indicator light malfunction*1 | Combination meter assembly (LED): Perform Active Test (Indicat. SET) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Cruise control SET indicator light circuit (Cruise SET indicator light circuit) | Refer to Cruise SET Indicator Light Circuit [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| Clearance sonar indicator light malfunction*2 | Combination meter assembly (LED): Perform Active Test (Indicat. INTUITIVE P/A LCD) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| *1: for Multi-information Display (Monochrome Type) *2: w/ Intuitive Parking Assist System *3: w/ Pre-collision System *4: w/ Tire Pressure Warning System *5: for AWD *6: w/ Automatic High Beam System *7: w/ Lane Departure Alert System *8: for Speedometer with Metric Units for Main Scale *9: for Speedometer with Imperial Units for Main Scale *10: w/ Front Fog Light |
||
MULTI-INFORMATION DISPLAY (MONOCHROME TYPE)
| Symptom | Suspected Area | Link |
|---|---|---|
| "Opening" display malfunction | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Odometer" display malfunction | Check customize parameters (ODO Display Time After IG OFF Setting) | Refer to CUSTOMIZE PARAMETERS [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| "TRIP A/TRIP B meter" display malfunction | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Eco driving indicator zone" display malfunction | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Current fuel consumption (Bar type)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Average fuel consumption (After reset)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Drivable distance" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Average fuel consumption (After refuel)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Driving distance (After reset)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Average speed (After reset)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Setting" display malfunction | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Other (Blank)" display malfunction | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Shift position" display malfunction | Automatic transaxle system (for U660E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Automatic transaxle system (for U660F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Automatic transaxle system (for U760E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Outside temp" display malfunction Air conditioning system | Air conditioning system (for Automatic Air Conditioning System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Air conditioning system (for Manual Air Conditioning System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Air conditioning amplifier assembly | Refer to REMOVAL [12/2013 - ] | |
| "ACCESSORY" display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "IGNITION ON" display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "AWD TEST MODE" display malfunction*1 | Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "ADJUSTING LDA CAMERA" display malfunction*2 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "HOLDING IN ENGINE SWITCH WILL CAUSE AN EMERGENCY ENGINE STOP." display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "TO RESTART CAR, SHIFT LEVER TO "N" AND PRESS ENGINE SWITCH." display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "THE ENGINE HAS STOPPED. PLEASE PUT SHIFT LEVER INTO "P"." display malfunction (Speedometer, tachometer and shift position indicator are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "THE ENGINE HAS STOPPED. PLEASE STOP YOUR CAR IN A SAFE PLACE." display malfunction (Speedometer, tachometer and shift position indicator are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Lane departure alert warning reminder indicator" display malfunction*2 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "THE ACCELERATOR IS STUCK. PLEASE DEPRESS BRAKE PEDAL TO STOP CAR." display malfunction | SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Each door open" display malfunction (Door courtesy switch or hood courtesy switch is normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| "Clearance sonar detection (image display)" display malfunction*4 | Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "CHECK SONAR" display malfunction*4 | Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "CLEAN SONAR" display malfunction*4 | Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "Glass door open" display malfunction (Glass hatch courtesy switch is normal)*5 | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| "AUTO POWER OFF TO CONSERVE BATTERY" display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "SHIFT TO P POSITION WHEN PARKED" display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "EPS FAILURE. STEERING WHEEL HARDER TO TURN." display malfunction | Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "VOLTAGE ABNORMALITY. STEERING WHEEL HARDER TO TURN." display malfunction | Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "CHECK POWER STEERING SYSTEM" display malfunction | Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "RELEASE PARKING BRAKE" display malfunction (Brake warning light is normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| "KEY NOT DETECTED" display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "LDA NOT AVAILABLE" display malfunction*2 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "CHECK SMART KEY SYSTEM" display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "BSM NOT AVAILABLE" display malfunction*6 | Blind spot monitor system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Blind spot monitor sensor LH | Refer to REMOVAL [12/2013 - 11/2016] | |
| "CHECK CRUISE CONTROL SYSTEM" display malfunction | Cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "CHECK LDA SYSTEM" display malfunction*2 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "CHECK BSM SYSTEM" display malfunction*6 | Blind spot monitor system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Blind spot monitor sensor LH | Refer to REMOVAL [12/2013 - 11/2016] | |
| "TRANSMISSION FLUID HIGH TEMPERATURE" display malfunction | Automatic transaxle system (for U660E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Automatic transaxle system (for U660F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Automatic transaxle system (for U760E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "CHECK AWD SYSTEM" display malfunction*1 | Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "LDA SYSTEM IS UNAVAILABLE BELOW APPROX. 50 KM/H." display malfunction*2 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "LDA SYSTEM IS UNAVAILABLE BELOW APPROX. 32 MPH." display malfunction*2 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "LDA SYSTEM IS UNAVAILABLE AT THIS SPEED." display malfunction*2 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Lane departure alert indicator" display malfunction*2 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "ENGINE STOPPED, STEERING WHEEL HARDER TO TURN." display malfunction | Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "TURN POWER OFF" display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "KEY DETECTED IN VEHICLE" display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "TURN LIGHT OFF" display malfunction | Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| "MOON ROOF OPENED" display malfunction*7 | Sliding roof system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| "DEPRESS BRAKE PEDAL, TOUCH ENGINE SWITCH WITH KEY" display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "DEPRESS BRAKE PEDAL AND PUSH ENGINE SWITCH TO START" display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "THE ACCELERATOR IS STUCK. PLEASE CHECK THE ACCELERATOR." display malfunction | SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "STEERING LOCK ACTIVE" display malfunction*3 | Steering lock system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "AWD SYSTEM OVERHEAT. 2WD SYSTEM ENGAGED" display malfunction*1 | Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "AWD SYSTEM OVERHEATED. SWITCHING TO 2WD MODE." display malfunction*1 | Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "BRAKE OVERRIDE SYSTEM FAILURE." display malfunction | SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "KEY BATTERY LOW" display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "CHECK HEADLIGHT SYSTEM" display malfunction*8 | Automatic high beam system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| "BOTH ACCELERATOR AND BRAKE PEDALS ARE DEPRESSED." display malfunction | SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "WASHER FLUID LOW" display malfunction | Combination meter assembly: Read the Data List (Washer Switch) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Level warning switch assembly | Refer to INSPECTION [12/2013 - ] | |
| Wire harness or connector (Combination meter assembly - Level warning switch assembly) | - | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| "FUEL LOW" display malfunction (Fuel receiver gauge is normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "TRAC OFF" display malfunction | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Brake actuator assembly (Skid control ECU) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "MAINTENANCE REQUIRED SOON" display malfunction*9 | Maintenance required reminder reset procedure | Refer to INITIALIZATION [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| "MAINTENANCE REQUIRED" display malfunction*9 | Maintenance required reminder reset procedure | Refer to INITIALIZATION [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| "TURN ON THE HIGH BEAM TO ACTIVATE AHB SYSTEM" display malfunction*8 | Automatic high beam system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| "RESETTING MAINTENANCE DATA" display malfunction*9 | Maintenance required reminder reset procedure | Refer to INITIALIZATION [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| "RESETTING MAINTENANCE DATA INCOMPLETE" display malfunction*9 | Maintenance required reminder reset procedure | Refer to INITIALIZATION [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| "Engine start possible condition (Smart key symbol)" display malfunction*3 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| *1: for AWD *2: w/ Lane Departure Alert System *3: w/ Smart Key System *4: w/ Intuitive Parking Assist System *5: w/ Glass Hatch Opener System *6: w/ Blind Spot Monitor System *7: w/ Sliding Roof System *8: w/ Automatic High Beam System *9: w/ Maintenance Required Reminder |
||
MULTI-INFORMATION DISPLAY (COLOR TYPE)
| Symptom | Suspected Area | Link |
|---|---|---|
| "Opening" display malfunction | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Odometer" display malfunction | Check customize parameters (ODO Display Time After IG OFF Setting) | Refer to CUSTOMIZE PARAMETERS [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| "TRIP A/TRIP B meter" display malfunction | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Current fuel consumption (Bar type)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Average fuel consumption (After reset)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Average fuel consumption (After start)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Average fuel consumption (After refuel)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Average speed (After reset)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Average speed (After reset)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Elapsed time (After reset)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Elapsed time (After start)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Drivable distance" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Driving distance (After reset)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Driving distance (After start)" display malfunction (Other meter functions are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Eco driving indicator zone" display malfunction | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "AWD control" display malfunction*1 | Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "Other (Blank)" display malfunction | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Drive information tab" display malfunction | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Navigation tab" display malfunction | Navigation system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Navigation receiver assembly | Refer to REMOVAL [12/2013 - ] | |
| "Audio tab" display malfunction | Navigation system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Navigation receiver assembly | Refer to REMOVAL [12/2013 - ] | |
| "Cruise control operation guide tab" display malfunction*3 | Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Message tab" display malfunction | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Setting tab" display malfunction | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Shift position" display malfunction | Automatic transaxle system (for U660E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Automatic transaxle system (for U660F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Automatic transaxle system (for U760E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "SNOW indicator light" display malfunction | Automatic transaxle system (for U660E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Automatic transaxle system (for U660F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Automatic transaxle system (for U760E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Cruise control SET indicator light" display malfunction | Cruise control SET indicator light circuit (w/ Dynamic Radar Cruise Control System) | Refer to Cruise SET Indicator Light Circuit [12/2013 - 11/2016] |
| Cruise control SET indicator light circuit (w/o Dynamic Radar Cruise Control System) | Refer to Cruise SET Indicator Light Circuit [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Cruise control indicator light" display malfunction*11 | Cruise control indicator light circuit (Cruise main indicator light circuit) | Refer to Cruise Main Indicator Light Circuit [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Cruise control indicator light (Constant speed control mode)" display malfunction*3 | Cruise control indicator light (Constant speed control mode) circuit (Cruise main indicator light circuit) | Refer to Cruise Main Indicator Light Circuit [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Cruise control indicator light (Vehicle-to-vehicle distance control mode)" display malfunction*3 | Cruise control indicator light (Vehicle-to-vehicle distance control mode) circuit (Cruise main indicator light circuit) | Refer to Cruise Main Indicator Light Circuit [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Lane departure alert indicator light" display malfunction*4 | Lane departure alert indicator light circuit (Indicator circuit) | Refer to Indicator Circuit [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Outside temp" display malfunction | Air conditioning system (for Automatic Air Conditioning System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Air conditioning system (for Manual Air Conditioning System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Air conditioning amplifier assembly | Refer to REMOVAL [12/2013 - ] | |
| "Icy street warning light" display malfunction | Air conditioning system (for Automatic Air Conditioning System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Air conditioning system (for Manual Air Conditioning System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Air conditioning amplifier assembly | Refer to REMOVAL [12/2013 - ] | |
| "Phone (Received Call)" display malfunction | Navigation system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Navigation receiver assembly | Refer to REMOVAL [12/2013 - ] | |
| "Turn-by-turn Navigation" display malfunction | Navigation system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Navigation receiver assembly | Refer to REMOVAL [12/2013 - ] | |
| "Cruise control main switch guide" display malfunction*3 | Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "ACCESSORY" display malfunction*5 | Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "IGNITION ON" display malfunction*5 | Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "AWD Test Mode" display malfunction*1 | Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "Adjusting LDA Camera" display malfunction*4 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Adjusting Front Radar Beam" display malfunction*3 | Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "BRAKE!" display malfunction*6 | Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "Holding in Engine Switch Will Cause an Emergency Engine Stop." display malfunction*5 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "To Restart Car, Shift Lever to "N" and Press Engine Switch." display malfunction*5 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "The Engine Has Stopped. Please Put Shift Lever into "P"." display malfunction (Speedometer, tachometer and shift position indicator are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "The Engine Has Stopped. Please Stop Your Car in a Safe Place." display malfunction (Speedometer, tachometer and shift position indicator are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "Dynamic radar cruise control warning reminder indicator (image display)" display malfunction*3 | Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Lane departure alert warning reminder indicator (image display)" display malfunction*4 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "The Accelerator is Stuck. Please Depress Brake Pedal to Stop Car." display malfunction | SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Each door open" display malfunction (Door courtesy switch, glass hatch courtesy switch or hood courtesy switch is normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| "Clearance sonar detection (image display)" display malfunction*7 | Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "Check Park Sonar System" display malfunction*7 | Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "Clean Park Sonar" display malfunction*7 | Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "Auto Power OFF to Conserve Battery" display malfunction*5 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "Shift to P position when parked" display malfunction*5 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "EPS Failure. Steering Wheel Harder to Turn." display malfunction | Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "Voltage Abnormality. Steering Wheel Harder to Turn." display malfunction | Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "Check Power Steering System" display malfunction | Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "Release Parking Brake" display malfunction (Brake warning light is normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| "Key not detected" display malfunction*5 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "Engine Coolant High Temperature" display malfunction (Engine coolant temperature receiver gauge is normal) | SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Clean Radar Sensor" display malfunction*3 | Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Cruise Control not available" display malfunction*3 | Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "LDA not available" display malfunction*4 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Check Smart Key System" display malfunction*5 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "BSM not available" display malfunction*8 | Blind spot monitor system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Blind spot monitor sensor LH | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Check Cruise Control System" display malfunction | Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Cruise control system (w/o Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Check LDA System" display malfunction*4 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Check PCS System" display malfunction*6 | Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "Check BSM System" display malfunction*8 | Blind spot monitor system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Blind spot monitor sensor LH | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Engine Oil Pressure Low" display malfunction | Combination meter assembly: Read the Data List (Oil Pressure Switch) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Engine oil pressure switch assembly (for 1AR-FE) | Refer to INSPECTION [12/2013 - ] | |
| Engine oil pressure switch assembly (for 2GR-FE) | Refer to INSPECTION [12/2013 - 11/2016] | |
| Wire harness or connector (Combination meter assembly - Engine oil pressure switch assembly) | - | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| "Transmission Fluid High Temperature" display malfunction | Automatic transaxle system (for U660E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Automatic transaxle system (for U660F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Automatic transaxle system (for U760E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Check AWD System" display malfunction*1 | Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "LDA System is Unavailable Below Approx. 50 km/h." display malfunction*4 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "LDA System is Unavailable Below Approx. 32 MPH." display malfunction*4 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "LDA System is Unavailable at this Speed." display malfunction*4 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Dynamic radar cruise control indicator (image display)" display malfunction*3 | Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Lane departure alert indicator (image display)" display malfunction*4 | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Engine Stopped, Steering Wheel Harder to Turn." display malfunction | Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "Turn Power OFF" display malfunction*5 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "Key detected in vehicle" display malfunction*5 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "Turn Light Off" display malfunction | Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| "Moon Roof opened" display malfunction*9 | Sliding roof system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| "Depress brake pedal, touch engine switch with key" display malfunction*5 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "Depress brake pedal and push engine switch to start" display malfunction*5 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "The Accelerator is Stuck. Please Check the Accelerator." display malfunction | SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Steering Lock active" display malfunction*5 | Steering lock system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "AWD system overheat. 2WD mode engaged" display malfunction*1 | Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "AWD system overheated. Switching to 2WD mode." display malfunction*1 | Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "Brake Override System Failure." display malfunction | SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Key Battery Low" display malfunction*5 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "Check Headlight System" display malfunction*10 | Automatic high beam system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| "Both Accelerator and Brake Pedals Are Depressed." display malfunction | SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Washer Fluid Low" display malfunction | Combination meter assembly: Read the Data List (Washer Switch) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Level warning switch assembly | Refer to INSPECTION [12/2013 - ] | |
| Wire harness or connector (Combination meter assembly - Level warning switch assembly) | - | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| "Fuel Low" display malfunction (Fuel receiver gauge is normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| "TRAC OFF" display malfunction | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Brake actuator assembly (Skid control ECU) | Refer to REMOVAL [12/2013 - 11/2016] | |
| "Maintenance required soon" display malfunction*2 | Maintenance required reminder reset procedure | Refer to INITIALIZATION [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| "Maintenance required" display malfunction*2 | Maintenance required reminder reset procedure | Refer to INITIALIZATION [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| "Turn on the high beam to activate AHB System" display malfunction*10 | Automatic high beam system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| "Resetting Maintenance Data" display malfunction*2 | Maintenance required reminder reset procedure | Refer to INITIALIZATION [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| "Resetting Maintenance Data incomplete" display malfunction*2 | Maintenance required reminder reset procedure | Refer to INITIALIZATION [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| "Depress brake pedal and push engine switch to start" display malfunction*5 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| "VSC System Switched Off. Pre-Collision Brake System Disengaged." display malfunction*6 | Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| "PCS temporarily not available" display malfunction*6 | Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [12/2013 - ] | |
| *1: for AWD *2: w/ Maintenance Required Reminder *3: w/ Dynamic Radar Cruise Control System *4: w/ Lane Departure Alert System *5: w/ Smart Key System *6: w/ Pre-collision System *7: w/ Intuitive Parking Assist System *8: w/ Blind Spot Monitor System *9: w/ Sliding Roof System *10: w/ Automatic High Beam System *11: w/o Dynamic Radar Cruise Control System |
||
BUZZER
| Symptom | Suspected Area | Link |
|---|---|---|
| All buzzers do not operate normally | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Seat belt warning (for driver side) buzzer malfunction (Seat belt warning light operation is normal) | Check customize parameters (Driver Side Seatbelt Warning Buzzer) | Refer to CUSTOMIZE PARAMETERS [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Restart while driving notification buzzer malfunction*1 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| Engine switch operation while driving warning buzzer malfunction*1 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| Seat belt warning (for front passenger side) buzzer malfunction (Seat belt warning light operation is normal) | Check customize parameters (Front Passenger Side Seatbelt Warning Buzzer) | Refer to CUSTOMIZE PARAMETERS [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Vehicle roll-away notification (STEP 1) buzzer malfunction (Speedometer, tachometer and shift position indicator are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Vehicle roll-away notification (STEP 2) buzzer malfunction (Speedometer, tachometer and shift position indicator are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Brake fluid low warning buzzer malfunction (Brake warning light is normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Oil pressure warning buzzer malfunction | Engine oil pressure switch assembly (for 1AR-FE) | Refer to INSPECTION [12/2013 - ] |
| Engine oil pressure switch assembly (for 2GR-FE) | Refer to INSPECTION [12/2013 - 11/2016] | |
| Wire harness or connector (Combination meter assembly - Engine oil pressure switch assembly) | - | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| EPS warning buzzer malfunction (EPS warning light is normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Engine coolant temperature warning buzzer malfunction (Engine coolant temperature receiver gauge is normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Smart key warning buzzer malfunction*1 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Smart key system (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| Key reminder buzzer malfunction | Smart key system (for Entry Function) (w/ Smart key System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Key reminder buzzer circuit (Key reminder buzzer does not sound) (w/o Smart key System) | Refer to Key Reminder Buzzer does not Sound [12/2013 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| Brake system temperature rise or active test buzzer malfunction | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Brake actuator assembly (Skid control ECU) | Refer to REMOVAL [12/2013 - 11/2016] | |
| Temperature warning buzzer malfunction | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Brake actuator assembly (Skid control ECU) | Refer to REMOVAL [12/2013 - 11/2016] | |
| Multi-information display warning buzzer malfunction (Master warning light is normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Radar cruise control low speed cancel buzzer malfunction*2 | Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| Immobiliser key identification completion buzzer malfunction*1 | Smart key system (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [12/2013 - ] | |
| Driving with parking brake unreleased warning buzzer malfunction (Speedometer and brake warning light are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| Driving with door open warning buzzer malfunction (Speedometer and door courtesy switch are normal) | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Sports shift reject buzzer malfunction | SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 1AR-FE) | Refer to REMOVAL [12/2013 - ] | |
| ECM (for 2GR-FE) | Refer to REMOVAL [12/2013 - 11/2016] | |
| Light reminder buzzer malfunction | Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| Sliding roof open warning buzzer malfunction*3 | Sliding roof system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [12/2013 - ] | |
| Turn signal flasher buzzer malfunction (Turn indicator light is normal) | Check customize parameters (Flasher Sound Volume Adjustment) | Refer to CUSTOMIZE PARAMETERS [12/2013 - ] |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| *1: w/ Smart Key System *2: w/ Dynamic Radar Cruise Control System *3: w/ Sliding Roof System |
||
OTHERS
| Symptom | Suspected Area | Link |
|---|---|---|
| "Diagnostic trouble code" display malfunction | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Operating ODO/TRIP switch knob does not change odometer/TRIP meter display | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Operating DISP switch (Steering pad switch assembly) does not change multi-information display*1 | Steering pad switch assembly | Refer to INSPECTION [12/2013 - 11/2016] |
| Spiral cable sub-assembly | Refer to INSPECTION [12/2013 - 11/2016] | |
| Wire harness or connector (Combination meter assembly - Spiral cable sub-assembly) | - | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Operating steering pad switch does not change multi-information display*2 | Combination meter assembly: Read the Data List (Multi Switch (UP), Multi Switch (Down), Multi Switch (Menu), Multi Switch (ENTER), Multi Switch (Right) or Multi Switch (Left)) | Refer to DATA LIST / ACTIVE TEST [12/2013 - 11/2016] |
| Steering pad switch assembly | Refer to INSPECTION [12/2013 - 11/2016] | |
| Spiral cable sub-assembly | Refer to INSPECTION [12/2013 - 11/2016] | |
| Wire harness or connector (Combination meter assembly - Spiral cable sub-assembly) | - | |
| Combination meter assembly | Refer to REMOVAL [12/2013 - ] | |
| Operating light control switch knob does not change light brightness | Combination meter assembly | Refer to REMOVAL [12/2013 - ] |
| Meter illumination is always dark | Illumination circuit (Meter illumination is always dark) | Refer to Meter Illumination is Always Dark [12/2013 - ] |
| Meter illumination does not dim at night | Illumination circuit (Meter illumination does not dim at night) | Refer to Meter Illumination does not Dim at Night [12/2013 - ] |
| Other systems that use the speed signal do not operate normally | Speed signal circuit | Refer to Speed Signal Circuit [12/2013 - 11/2015] Refer to Speed Signal Circuit [11/2015 - 11/2016] |
| *1: for Multi-information Display (Monochrome Type) *2: for Multi-information Display (Color Type) |
||