DTC C2171/71: Transmitter ID not Registered [10/2014 - ]: Procedure
- CONFIRM REGISTRATION CONDITION (REGISTERED ID CODES)
- Turn the engine switch off.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
- Check the values by referring to the table below.TIRE PRESSURE MONITOR
Tester Display Measurement Item/Range Normal Condition Diagnostic Note Registered ID 1 code Registered ID1 code/
min.: 0
max.: FFFFFFF*1ID No. registered for transmitter ID1 displayed - Registered ID 2 code Registered ID2 code/
min.: 0
max.: FFFFFFF*1ID No. registered for transmitter ID2 displayed - Registered ID 3 code Registered ID3 code/
min.: 0
max.: FFFFFFF*1ID No. registered for transmitter ID3 displayed - Registered ID 4 code Registered ID4 code/
min.: 0
max.: FFFFFFF*1ID No. registered for transmitter ID4 displayed - HINT:
*1: Displayed only when the ID No. is not registered.
OK
The registered transmitter ID codes are displayed on the Techstream.
Result:
OK
REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
(Refer to REMOVAL [10/2014 - ] )
Result:
NG
See step 2
- PERFORM REGISTRATION (TRANSMITTER ID)
- Perform registration (Refer to REGISTRATION [10/2014 - 10/2015] or REGISTRATION [10/2015 - ] ).
Result:
NEXT
See step 3
- PERFORM INITIALIZATION
- Perform initialization (Refer to INITIALIZATION [10/2014 - 10/2015] or INITIALIZATION [10/2015 - ] ).
Result:
NEXT
See step 4
- CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
- Turn the engine switch off.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
- Check the values by referring to the table below.TIRE PRESSURE MONITOR
Tester Display Measurement Item/Range Normal Condition Diagnostic Note ID 1 Tire Inflation Pressure ID1 tire inflation pressure/
min.: Absolute pressure (abs) / 50 kPa (0.5 kgf/cm2 , 7 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2 , 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2 , 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2 , 55 psi)Actual tire inflation pressure If N/A is displayed, data has not been received.*1 ID 2 Tire Inflation Pressure ID2 tire inflation pressure/
min.: Absolute pressure (abs) / 50 kPa (0.5 kgf/cm2 , 7 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2 , 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2 , 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2 , 55 psi)Actual tire inflation pressure If N/A is displayed, data has not been received.*1 ID 3 Tire Inflation Pressure ID3 tire inflation pressure/
min.: Absolute pressure (abs) / 50 kPa (0.5 kgf/cm2 , 7 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2 , 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2 , 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2 , 55 psi)Actual tire inflation pressure If N/A is displayed, data has not been received.*1 ID 4 Tire Inflation Pressure ID4 tire inflation pressure/
min.: Absolute pressure (abs) / 50 kPa (0.5 kgf/cm2 , 7 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2 , 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2 , 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2 , 55 psi)Actual tire inflation pressure If N/A is displayed, data has not been received.*1 HINT:
- *1: It may take a few minutes until the values are displayed.
- When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.
Result
Result Proceed to All tire pressure readings are equal to specified values. A Tire pressure values are not displayed. B
Result:
A
END
Result:
B
REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
(Refer to REMOVAL [10/2014 - ] )