LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2015 >> Avalon XLE >> Repair and Diagnosis >> Accessories & Equipment >> Communication Devices >> Can Communication System (W/O Central Gateway Ecu) - Diagnostic Codes & Circuit Tests - (Except Hybrid) >> CAN COMMUNICATION SYSTEM (W/O Central Gateway ECU) >> Circuit Tests >> Check CAN Bus Line for Short to +B [10/2014 - 10/2015] >> Procedure

Check CAN Bus Line for Short to +B [10/2014 - 10/2015]: Procedure

  1. CHECK FOR SHORT TO +B IN CAN BUS LINE (DLC3 BRANCH LINE) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the D75 DLC3 branch line connector.
      GTY565007Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 1 CAN Junction Connector)
      *b to DLC3
      NOTE:
      • Before disconnecting the connector, make a note of where it is connected.
      • Reconnect the connector to its original position.
    3. Measure the resistance according to the value (s) in the table below.
      GTY583410Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 DLC3

      Standard Resistance

      Tester Connection Condition Specified Condition
      D28-6 (CANH) - D28-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D28-14 (CANL) - D28-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

    NG 

    REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3 

    OK 

    See step  2

  2. CHECK FOR SHORT TO +B IN CAN BUS LINE 
    1. Reconnect the D75 DLC3 branch line connector.
    2. Disconnect the connectors from the No. 1 CAN junction connector and No. 2 CAN junction connector one at a time.

      HINT: 

      Disconnect the ECU and sensor connectors other than the DLC3 branch lines and CAN main bus lines between the No. 1 CAN junction connector and No. 2 CAN junction connector.

      GTY583410Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 DLC3
    3. Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.
      GTY550785Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *A for Navigation Receiver Type *B for Radio and Display Type
      *C w/ Pre-collision System and/or Blind Spot Monitor System - -
      *1 Power Steering ECU Assembly *2 Steering Sensor
      *3 DLC3 *4 Main Body ECU (Multiplex Network Body ECU)
      *5 Combination Meter Assembly *6 Airbag ECU Assembly
      *7 Skid Control ECU (Brake Actuator Assembly) *8 Network Gateway ECU
      *9 Navigation ECU Sub-assembly *10 Radio and Display Receiver Assembly
      *11 Certification ECU (Smart Key ECU Assembly) *12 ECM
      *13 Air Conditioning Amplifier Assembly *14 No. 1 CAN Junction Connector
      *15 No. 2 CAN Junction Connector - -
      GTY558885Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (No. 1 CAN Junction Connector)      		 - -
      WIRING COLOR

      No. 1 CAN Junction Connector Side Code Color (CANH Side) Color (CANL Side)
      Airbag ECU assembly D80 LG W
      Combination meter assembly D73 R W
      Main body ECU (Multiplex network body ECU) D74 P W
      DLC3 D75 L W
      Steering sensor D76 V W
      Power steering ECU assembly D77 G W
      CAN main bus line (bus line connecting No. 1 CAN junction connector and No. 2 CAN junction connector) D72 B W
      GTY601017Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (No. 2 CAN Junction Connector)      		 - -
      WIRING COLOR

      No. 2 CAN Junction Connector Side Code Color (CANH Side) Color (CANL Side)
      CAN main bus line (bus line connecting No. 1 CAN junction connector and No. 2 CAN junction connector) D78 B W
      Air conditioning amplifier assembly D79 BR W
      ECM D81 P W
      Certification ECU (Smart key ECU assembly) D83 L W
      • Navigation ECU sub-assembly*1
      • Radio and display receiver assembly*2
      		 D84 R W
      Network gateway ECU*3 D85 SB W
      Skid control ECU (Brake actuator assembly) D82 GR W
      • *1: for Navigation receiver type
      • *2: for Radio and display type
      • *3: w/ Pre-collision system and/or blind spot monitor system
      NOTE:

      Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to +B in 2 or more CAN bus lines.

      Result

      Symptom Proceed to
      The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector. (There is a short to +B in the CAN main bus lines between the No. 1 CAN junction connector and No. 2 CAN junction connector.) A
      The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) becomes normal (6 kΩ or more) when a connector is disconnected from the CAN junction connector. (There is a short to +B in one of the areas that relate to one or more of the disconnected bus lines.) B
    4. When there is a short to +B in one or more of the bus lines that connect to an ECU (or sensor) :
      1. Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to +B). Check that the resistance shown on the tester is normal (6 kΩ or more) to confirm that there is a short to +B in the one bus line only.

        HINT: 

        • Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.
        • Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
    5. When there is no short to +B in any of the bus lines that connect to the ECUs and sensors:
      1. With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the No. 1 CAN junction connector and No. 2 CAN junction connector.

    B 

    See step  5

    A 

    See step  3

  3. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 CAN J/C) 
    1. Disconnect the D72 CAN main bus line connector.
      GTY562093Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 1 CAN Junction Connector)
      *b to No. 2 CAN Junction Connector
      NOTE:
      • Before disconnecting the connector, make a note of where it is connected.
      • Reconnect the connector to its original position.
    2. Measure the resistance according to the value (s) in the table below.
      GTY583410Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 DLC3

      Standard Resistance

      Tester Connection Condition Specified Condition
      D28-6 (CANH) - D28-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D28-14 (CANL) - D28-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

    NG 

    REPLACE NO. 1 CAN JUNCTION CONNECTOR 

    OK 

    See step  4

  4. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 CAN J/C - NO. 2 CAN J/C) 
    1. Reconnect the D72 CAN main bus line connector.
    2. Disconnect the D78 CAN main bus line connector.
      GTY570517Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Rear view of wire harness connector
      (to No. 2 CAN Junction Connector)
      *b to No. 1 CAN Junction Connector
      NOTE:
      • Before disconnecting the connector, make a note of where it is connected.
      • Reconnect the connector to its original position.
    3. Measure the resistance according to the value (s) in the table below.
      GTY583410Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 DLC3

      Standard Resistance

      Tester Connection Condition Specified Condition
      D28-6 (CANH) - D28-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D28-14 (CANL) - D28-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

    OK 

    REPLACE NO. 2 CAN JUNCTION CONNECTOR 

    NG 

    REPAIR OR REPLACE CAN MAIN BUS LINE (NO. 1 CAN J/C - NO. 2 CAN J/C) 

  5. CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR) 
    1. Reconnect the connector of the bus line that is shorted to +B to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or more when it was disconnected).
    2. Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the bus line shorted to +B is connected (Refer to TERMINALS OF ECU [10/2014 - 10/2015] ).
      GTY583410Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 DLC3
    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D28-6 (CANH) - D28-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      D28-14 (CANL) - D28-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

      HINT: 

      If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).

    OK 

    REPLACE CORRESPONDING ECU OR SENSOR 

    NG 

    REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR 

scientia non olet · About LEMON Manuals