LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2015 >> Avalon Hybrid Limited >> Repair and Diagnosis >> Hybrid/Electric Powertrain >> Testing and Diagnosis >> Hybrid Control System - Diagnostic Codes (8 Of 8) - Symptom & Circuit Tests - (Hybrid) >> Hybrid Control System >> Circuit Tests >> Pattern Select Switch Sport Mode Circuit [10/2015 - ] >> Procedure

Pattern Select Switch Sport Mode Circuit [10/2015 - ]: Procedure

  1. READ VALUE USING TECHSTREAM (CAN BUS CHECK) 

    See step  2

    Result: 

    B 

    GO TO CAN COMMUNICATION SYSTEM 

    for w/ Central Gateway ECU: Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2015 - ]

    for w/o Central Gateway ECU: Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2015 - ]

    Result: 

    A 

    See step  2

  2. CHECK DTC OUTPUT (HEALTH CHECK) 

    See step  3

    Result: 

    B 

    GO TO APPLICABLE DTC CHART 

    Result: 

    A 

    See step  3

  3. PERFORM ACTIVE TEST USING TECHSTREAM (INDICAT. SPORT (CVT SPORT)) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (READY).
    3. Enter the following menus: Body Electrical / Combination Meter / Active Test / Indicat. Sport (CVT Sport).
    4. Perform the "Indicat. Sport (CVT Sport)" Active Test.

      OK

      The SPORT indicator light comes on or blinks.

    5. Turn the power switch off.

    Result: 

    NG 

    REPLACE COMBINATION METER ASSEMBLY 

    (Refer to COMPONENTS [10/2015 - ] )

    Result: 

    OK 

    See step  4

  4. READ VALUE USING TECHSTREAM (PATTERN SWITCH (PWR/M)) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Powertrain / Hybrid Control / Data List / Pattern Switch (PWR/M).
    4. Read the value displayed on the Techstream.
      Tester Display Measurement Item/Range Normal Condition
      Pattern Switch (PWR/M) SPORT mode transition availability/
      ON or OFF      		 In SPORT mode: ON

      Result

      Result Proceed to
      The Techstream display changes according to the SPORT mode switch (combination switch assembly) operation. A
      The Techstream display does not change according to the SPORT mode switch (combination switch assembly) operation. B

    Result: 

    A 

    CHECK FOR INTERMITTENT PROBLEMS 

    (Refer to CHECK FOR INTERMITTENT PROBLEMS [10/2014 - ] )

    Result: 

    B 

    See step  5

  5. READ VALUE USING TECHSTREAM (SPORT MODE SWITCH) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Powertrain / Engine and ECT / Data List / Sports Mode Switch.
    4. Read the value displayed on the Techstream.
      Tester Display Measurement Item/Range Normal Condition
      Sports Mode Switch SPORT mode switch (combination switch assembly) condition /
      ON or OFF      		 SPORT mode switch (combination switch assembly) being pushed and held: ON
      SPORT mode switch (combination switch assembly) not pushed: OFF

      Result

      Result Proceed to
      The Techstream display changes according to the SPORT mode switch (combination switch assembly) operation. A
      The Techstream display does not change according to the SPORT mode switch (combination switch assembly) operation. B

    Result: 

    A 

    REPLACE ECM 

    (Refer to COMPONENTS [10/2014 - ] )

    Result: 

    B 

    See step  6

  6. CHECK SPORT MODE SWITCH (COMBINATION SWITCH ASSEMBLY) 
    1. Remove the SPORT mode switch (combination switch assembly) (Refer to COMPONENTS [10/2014 - ] ).
    2. Measure the resistance according to the value(s) in the table below.
      GTY553649Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (SPORT Mode Switch (Combination Switch Assembly))

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (PWR) - 3 (E) SPORT mode switch (combination switch assembly) being pushed and held Below 1 Ω
      SPORT mode switch (combination switch assembly) not pushed 10 kΩ or higher
    3. Install the SPORT mode switch (combination switch assembly).

    Result: 

    NG 

    REPLACE SPORT MODE SWITCH (COMBINATION SWITCH ASSEMBLY) 

    (Refer to COMPONENTS [10/2014 - ] )

    Result: 

    OK 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (SPORT MODE SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND) 
    1. Disconnect the D107 SPORT mode switch (combination switch assembly) connector.
    2. Measure the resistance according to the value(s) in the table below.
      GTY549791Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to SPORT Mode Switch (Combination Switch Assembly))

      Standard Resistance

      Tester Connection Condition Specified Condition
      D107-3 (E) - Body ground Always Below 1 Ω
    3. Reconnect the D107 SPORT mode switch (combination switch assembly) connector.

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  8

  8. CHECK HARNESS AND CONNECTOR (ECM - SPORT MODE SWITCH (COMBINATION SWITCH ASSEMBLY)) 
    1. Disconnect the A18 ECM connector.
    2. Disconnect the D107 SPORT mode switch (combination switch assembly) connector.
    3. Measure the resistance according to the value(s) in the table below.
      GTY597791Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to ECM)
      *b Front view of wire harness connector
      (to SPORT Mode Switch (Combination Switch Assembly))

      Standard Resistance

      Tester Connection Condition Specified Condition
      A18-9 (PWMS) - D107-1 (PWR) Always Below 1 Ω
      A18-9 (PWMS) or D107-1 (PWR) - Body ground Always 10 kΩ or higher
    4. Reconnect the D107 SPORT mode switch (combination switch assembly) connector.
    5. Reconnect the A18 ECM connector.

    Result: 

    OK 

    REPLACE ECM 

    (Refer to COMPONENTS [10/2014 - ] )

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals