VC Output Circuit [10/2014 - ]: Procedure

1. Check That The Malfunction Indicator Lamp (Mil) Lights Up When The Power Switch Is Turned On (Ig).

   Ok

   Mil Lights Up.

Result: 

Ok 

Proceed To Next Suspected Area Shown In Problem Symptoms Table 

(Refer to Problem Symptoms Table [10/2014 - ] )

Result: 

Ng 

See Step  2

1. Connect The Techstream To The Dlc3.
2. Turn The Power Switch On (Ig).
3. Turn The Techstream On.
4. Check The Communication Between The Techstream And ECM.
   Result
   
   

   Result	Proceed To
   Communication Is Not Possible	A
   Communication Is Possible	B

Result: 

B 

Go To Mil Circuit 

(Refer to Mil Circuit [10/2014 - 10/2015]  or Mil Circuit [10/2015 - ] )

Result: 

A 

See Step  3

1. Disconnect The Throttle With Motor Body Assembly Connector.
2. Turn The Power Switch On (Ig).
3. Check The Mil.
   Result
   
   

   Result	Proceed To
   Mil Does Not Illuminate	A
   Mil Illuminates	B

   Hint: 

   Perform "Inspection After Repair" After Replacing The Throttle With Motor Body Assembly (Refer to Initialization [10/2014 - ] ).

Result: 

B 

Replace Throttle With Motor Body Assembly 

(Refer to Removal [10/2014 - ] )

Result: 

A 

See Step  4

1. Disconnect The Camshaft Position Sensor Connector.
2. Turn The Power Switch On (Ig).
3. Check The Mil.
   Result
   
   

   Result	Proceed To
   Mil Does Not Illuminate	A
   Mil Illuminates	B

Result: 

B 

Replace Camshaft Position Sensor 

(Refer to Removal [10/2014 - ] )

Result: 

A 

See Step  5

1. Disconnect The Manifold Absolute Pressure Sensor Connector.
2. Turn The Power Switch On (Ig).
3. Check The Mil.
   Result
   
   

   Result	Proceed To
   Mil Does Not Illuminate	A
   Mil Illuminates	B

Result: 

B 

Replace Manifold Absolute Pressure Sensor 

(Refer to Removal [10/2014 - ] )

Result: 

A 

See Step  6

1. Disconnect The Canister Pump Module Connector.
2. Turn The Power Switch On (Ig).
3. Check The Mil.
   Result
   
   

   Result	Proceed To
   Mil Does Not Illuminate	A
   Mil Illuminates	B

Result: 

B 

Replace Canister Pump Module 

(Refer to Removal [10/2014 - ] )

Result: 

A 

See Step  7

1. Disconnect The Throttle With Motor Body Assembly Connector.
2. Disconnect The Camshaft Position Sensor Connector.
3. Disconnect The Manifold Absolute Pressure Sensor Connector.
4. Disconnect The Canister Pump Module Connector.
5. Disconnect The ECM Connectors.
6. Measure The Resistance According To The Value(S) In The Table Below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   B51-125 (VCta) - Body Ground	Always	10 KΩ Or Higher
   B51-113 (VCv1) - Body Ground	Always	10 KΩ Or Higher
   B51-78 (VCpm) - Body Ground	Always	10 KΩ Or Higher
   A18-34 (VCpp) - Body Ground	Always	10 KΩ Or Higher

Result: 

Ok 

Replace ECM 

(Refer to Removal [10/2014 - ] )

Result: 

Ng 

Repair Or Replace Harness Or Connector