LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2015 >> Avalon Hybrid Limited >> Repair and Diagnosis >> Engine Performance >> Testing & Diagnosis >> SFI System - Diagnostic Codes & Circuit Tests - (Hybrid) (4 Of 4) >> SFI System >> Circuit Tests >> ECM Power Source Circuit [10/2014 - 10/2015] >> Procedure

ECM Power Source Circuit [10/2014 - 10/2015]: Procedure

  1. Check Harness And Connector (ECM - Body Ground) 
    1. Disconnect The ECM Connector.
    2. Measure The Resistance According To The Value(S) In The Table Below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B51-16 (E1) - Body Ground Always Below 1 Ω

    Result: 

    Ng 

    Repair Or Replace Harness Or Connector 

    Result: 

    Ok 

    See Step  2

  2. Check Terminal Voltage (IGSW Voltage) 
    1. Disconnect The ECM Connector.
      GTY589544Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn The Power Switch On (Ig).
    3. Measure The Voltage According To The Value(S) In The Table Below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      A18-37 (IGSW) - Body Ground Power Switch On (Ig) 11 To 14 V
      Text In Illustration

      *A Front View Of Wire Harness Connector
      (To ECM)

    Result: 

    Ng 

    See Step  6

    Result: 

    Ok 

    See Step  3

  3. Inspect No. 1 Integration Relay (EFI Main Relay) 
    1. Inspect The No. 1 Integration Relay (EFI Main Relay) (Refer to Inspection [10/2014 - ] ).

    Result: 

    Ng 

    Replace No. 1 Integration Relay (EFI Main Relay) 

    (Refer to Removal [10/2014 - ] )

    Result: 

    Ok 

    See Step  4

  4. Check Harness And Connector (No. 1 Integration Relay - ECM) 
    1. Remove The No. 1 Integration Relay From The Engine Room Relay Block And Junction Block Assembly.
    2. Disconnect The ECM Connector.
    3. Measure The Resistance According To The Value(S) In The Table Below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      1C-9 - A18-2 (+B) Always Below 1 Ω
      1C-10 - A18-3 (+B2) Always Below 1 Ω
      1C-7 - A18-46 (MREL) Always Below 1 Ω
      1C-9 Or A18-2 (+B) - Body Ground Always 10 KΩ Or Higher
      1C-10 Or A18-3 (+B2) - Body Ground Always 10 KΩ Or Higher
      1C-7 Or A18-46 (MREL) - Body Ground Always 10 KΩ Or Higher

    Result: 

    Ng 

    Repair Or Replace Harness Or Connector 

    Result: 

    Ok 

    See Step  5

  5. Check Terminal Voltage (Power Source Of No. 1 Integration Relay) 
    1. Remove The No. 1 Integration Relay From The Engine Room Relay Block And Junction Block Assembly.
      GTY564744Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure The Voltage According To The Value(S) In The Table Below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      1B-1 - Body Ground Always 11 To 14 V
      Text In Illustration

      *A Front View Of Wire Harness Connector
      (To No. 1 Integration Relay)

    Result: 

    Ok 

    Proceed To Next Suspected Area Shown In Problem Symptoms Table 

    (Refer to Problem Symptoms Table [10/2014 - ] )

    Result: 

    Ng 

    Repair Or Replace Harness Or Connector (Auxiliary Battery - No. 1 Integration Relay) 

  6. Inspect No. 1 Integration Relay (Ig2 Relay) 
    1. Inspect The No. 1 Integration Relay (Ig2 Relay) (Refer to Inspection [10/2014 - ] ).

    Result: 

    Ng 

    Replace No. 1 Integration Relay (Ig2 Relay) 

    (Refer to Removal [10/2014 - ] )

    Result: 

    Ok 

    See Step  7

  7. Check Harness And Connector (No. 1 Integration Relay - ECM) 
    1. Remove The No. 1 Integration Relay From The Engine Room Relay Block And Junction Block Assembly.
    2. Disconnect The ECM Connector.
    3. Measure The Resistance According To The Value(S) In The Table Below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      1C-1 - A18-37 (IGSW) Always Below 1 Ω
      1C-1 Or A18-37 (IGSW) - Body Ground Always 10 KΩ Or Higher

    Result: 

    Ng 

    Repair Or Replace Harness Or Connector 

    Result: 

    Ok 

    See Step  8

  8. Check Terminal Voltage (Power Source Of No. 1 Integration Relay) 
    1. Remove The No. 1 Integration Relay From The Engine Room Relay Block And Junction Block Assembly.
      GTY555735Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure The Voltage According To The Value(S) In The Table Below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      1D-3 - Body Ground Always 11 To 14 V
      Text In Illustration

      *A Front View Of Wire Harness Connector
      (To No. 1 Integration Relay)

    Result: 

    Ng 

    Repair Or Replace Harness Or Connector (Auxiliary Battery - No. 1 Integration Relay) 

    Result: 

    Ok 

    See Step  9

  9. Check Harness And Connector (No. 1 Integration Relay - Body Ground) 
    1. Remove The No. 1 Integration Relay From The Engine Room Relay Block And Junction Block Assembly.
    2. Measure The Resistance According To The Value(S) In The Table Below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      1E-2 - Body Ground Always Below 1 Ω

    Result: 

    Ng 

    Repair Or Replace Harness Or Connector 

    Result: 

    Ok 

    See Step  10

  10. Check Harness And Connector (Power Management Control ECU - No. 1 Integration Relay 
    1. Disconnect The Power Management Control ECU Connector.
    2. Remove The No. 1 Integration Relay From The Engine Room Relay Block And Junction Block Assembly.
    3. Measure The Resistance According To The Value(S) In The Table Below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A54-2 (Ig2D) - 1C-8 Always Below 1 Ω
      A54-2 (Ig2D) Or 1C-8 - Body Ground Always 10 KΩ Or Higher

    Result: 

    Ok 

    Go To Smart Key System 

    (Refer to How To Proceed With Troubleshooting [10/2014 - 10/2015] )

    Result: 

    Ng 

    Repair Or Replace Harness Or Connector 

scientia non olet · About LEMON Manuals