LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2015 >> Avalon Hybrid Limited >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Navigation System - Diagnostic Codes & Symptom Tests - (Hybrid) >> Navigation System >> DTC B15C3: Speaker Output Short [10/2014 - ] >> Procedure

DTC B15C3: Speaker Output Short [10/2014 - ]: Procedure

  1. CONFIRM MODEL 
    1. Choose the model to be inspected.

      Result

      Result Proceed to
      for 9 Speakers A
      for 11 Speakers B

    Result: 

    B 

    See step  15

    Result: 

    A 

    See step  2

  2. CONFIRM MODEL 
    1. Choose the model to be inspected.

      Result

      Result Proceed to
      w/ Manual (SOS) Switch A
      w/o Manual (SOS) Switch B

    Result: 

    B 

    See step  7

    Result: 

    A 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - BODY GROUND) 
    1. Disconnect the I6 and I7 navigation ECU sub-assembly connectors.
    2. Disconnect the I135 DCM (telematics transceiver) connector.
    3. Disconnect the I1 front No. 2 speaker assembly LH connector.
    4. Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.
    5. Measure the resistance between the navigation ECU sub-assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I6-1 (FR+) - Body ground Always 10 kΩ or higher
      I6-5 (FR-) - Body ground Always 10 kΩ or higher
      I6-2 (FL+) - Body ground Always 10 kΩ or higher
      I6-6 (FL-) - Body ground Always 10 kΩ or higher
      I7-1 (RR+) - Body ground Always 10 kΩ or higher
      I7-3 (RR-) - Body ground Always 10 kΩ or higher
      I7-2 (RL+) - Body ground Always 10 kΩ or higher
      I7-6 (RL-) - Body ground Always 10 kΩ or higher

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - BODY GROUND) 
    1. Disconnect the I135 DCM (telematics transceiver) connector.
    2. Disconnect the I83 front No. 2 speaker assembly RH connector.
    3. Measure the resistance between the DCM (telematics transceiver) and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I135-5 (SPO+) - Body ground Always 10 kΩ or higher
      I135-6 (SPO-) - Body ground Always 10 kΩ or higher

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND) 
    1. Disconnect the I83 and I1 front No. 2 speaker assembly connectors.
    2. Disconnect the I60 front No. 3 speaker assembly connector.
    3. Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I83-3 (+) - Body ground Always 10 kΩ or higher
      I83-1 (-) - Body ground Always 10 kΩ or higher
      I1-3 (+) - Body ground Always 10 kΩ or higher
      I1-1 (-) - Body ground Always 10 kΩ or higher

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  6

  6. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Remove the DCM (telematics transceiver) (Refer to REMOVAL [10/2014 - ] ).
    2. Measure the resistance according to the value(s) in the table below.
      GTY473616Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher
    3. Proceed to the next step based on the inspection result.

      Result

      Result Proceed to
      NG A
      OK B
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (DCM (Telematics Transceiver))

    Result: 

    A 

    REPLACE DCM (TELEMATICS TRANSCEIVER) 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    B 

    See step  9

  7. CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - BODY GROUND) 
    1. Disconnect the I6 and I7 navigation ECU sub-assembly connectors.
    2. Disconnect the I83 and I1 front No. 2 speaker assembly connectors.
    3. Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.
    4. Measure the resistance between the navigation ECU sub-assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I6-1 (FR+) - Body ground Always 10 kΩ or higher
      I6-5 (FR-) - Body ground Always 10 kΩ or higher
      I6-2 (FL+) - Body ground Always 10 kΩ or higher
      I6-6 (FL-) - Body ground Always 10 kΩ or higher
      I7-1 (RR+) - Body ground Always 10 kΩ or higher
      I7-3 (RR-) - Body ground Always 10 kΩ or higher
      I7-2 (RL+) - Body ground Always 10 kΩ or higher
      I7-6 (RL-) - Body ground Always 10 kΩ or higher

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  8

  8. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND) 
    1. Disconnect the I83 and I1 front No. 2 speaker assembly connectors.
    2. Disconnect the I60 front No. 3 speaker assembly connector.
    3. Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I83-3 (+) - Body ground Always 10 kΩ or higher
      I83-1 (-) - Body ground Always 10 kΩ or higher
      I1-3 (+) - Body ground Always 10 kΩ or higher
      I1-1 (-) - Body ground Always 10 kΩ or higher

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  9

  9. INSPECT REAR NO. 2 SPEAKER ASSEMBLY 
    1. Remove the rear No. 2 speaker assembly (Refer to REMOVAL [10/2014 - ] ).
    2. Measure the resistance according to the value(s) in the table below.
      GTY382828Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      4 - 2 Always 10 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Rear No. 2 Speaker Assembly)

    Result: 

    NG 

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    OK 

    See step  10

  10. REPLACE REAR NO. 2 SPEAKER ASSEMBLY 
    1. Replace the rear No. 2 speaker assembly with a new or known good one (Refer to REMOVAL [10/2014 - ] ).
    2. Clear the DTCs (Refer to DTC CHECK / CLEAR [10/2014 - ] ).
    3. Recheck for DTCs and check that no DTCs are output.

      OK

      No DTCs are output.

      HINT: 

      • Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
      • When there is a possibility that either the right or left rear No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
      • Perform the above inspection on both the LH and RH side.

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  11

  11. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly (Refer to REMOVAL [10/2014 - ] ).
    2. Measure the resistance according to the value(s) in the table below.
      GTY482539Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      FOR LH

      Tester Connection Condition Specified Condition
      4 (TWL+) - 2 (TWL-) Always 10 kΩ or higher
      3 (+) - 4 (TWL+) Always Below 1 Ω
      1 (-) - 2 (TWL-) Always Below 1 Ω
      FOR RH

      Tester Connection Condition Specified Condition
      4 (TWR+) - 2 (TWR-) Always 10 kΩ or higher
      3 (+) - 4 (TWR+) Always Below 1 Ω
      1 (-) - 2 (TWR-) Always Below 1 Ω
      TEXT IN ILLUSTRATION

      *A for RH
      *B for LH
      *a Component without harness connected
      (Front No. 2 Speaker Assembly)

    Result: 

    NG 

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    OK 

    See step  12

  12. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Replace the front No. 2 speaker assembly with a new or known good one (Refer to REMOVAL [10/2014 - ] ).
    2. Clear the DTCs (Refer to DTC CHECK / CLEAR [10/2014 - ] ).
    3. Recheck for DTCs and check that no DTCs are output.

      OK

      No DTCs are output.

      HINT: 

      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
      • Perform the above inspection on both the LH and RH side.

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  13

  13. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY 
    1. Remove the front No. 3 speaker assembly (Refer to REMOVAL [10/2014 - ] ).
    2. Measure the resistance according to the value(s) in the table below.
      GTY562585Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      4 (+) - 2 (-) Always 10 kΩ or higher
      3 (+) - 1 (-) Always 10 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Front No. 3 Speaker Assembly)

    Result: 

    NG 

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    OK 

    See step  14

  14. REPLACE FRONT NO. 3 SPEAKER ASSEMBLY 
    1. Replace the front No. 3 speaker assembly with a new or known good one (Refer to REMOVAL [10/2014 - ] ).
    2. Clear the DTCs (Refer to DTC CHECK / CLEAR [10/2014 - ] ).
    3. Recheck for DTCs and check that no DTCs are output.

      OK

      No DTCs are output.

    Result: 

    OK 

    END 

    Result: 

    NG 

    REPLACE NAVIGATION ECU SUB-ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

  15. CONFIRM MODEL 
    1. Choose the model to be inspected.

      Result

      Result Proceed to
      w/ Manual (SOS) Switch A
      w/o Manual (SOS) Switch B

    Result: 

    B 

    See step  19

    Result: 

    A 

    See step  16

  16. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND) 
    1. Disconnect the E9 stereo component amplifier assembly connector.
    2. Disconnect the I135 DCM (telematics transceiver) connector.
    3. Disconnect the K5 front No. 2 speaker assembly LH connector.
    4. Disconnect the I84 and I2 front No. 1 speaker assembly connectors.
    5. Disconnect the I60 front No. 3 speaker assembly connector.
    6. Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.
    7. Disconnect the K14 and K15 rear header speaker assembly connectors.
    8. Disconnect the K13 and K16 rear speaker assembly connectors.
    9. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      E9-12 (TWR+) - Body ground Always 10 kΩ or higher
      E9-27 (TWR-) - Body ground Always 10 kΩ or higher
      E9-11 (TWL+) - Body ground Always 10 kΩ or higher
      E9-26 (TWL-) - Body ground Always 10 kΩ or higher
      E9-15 (FR+) - Body ground Always 10 kΩ or higher
      E9-30 (FR-) - Body ground Always 10 kΩ or higher
      E9-4 (FL+) - Body ground Always 10 kΩ or higher
      E9-19 (FL-) - Body ground Always 10 kΩ or higher
      E9-13 (CTR+) - Body ground Always 10 kΩ or higher
      E9-28 (CTR-) - Body ground Always 10 kΩ or higher
      E9-6 (RR+) - Body ground Always 10 kΩ or higher
      E9-21 (RR-) - Body ground Always 10 kΩ or higher
      E9-5 (RL+) - Body ground Always 10 kΩ or higher
      E9-20 (RL-) - Body ground Always 10 kΩ or higher
      E9-10 (SR+) - Body ground Always 10 kΩ or higher
      E9-25 (SR-) - Body ground Always 10 kΩ or higher
      E9-9 (SL+) - Body ground Always 10 kΩ or higher
      E9-24 (SL-) - Body ground Always 10 kΩ or higher
      E9-7 (WF2+) - Body ground Always 10 kΩ or higher
      E9-22 (WF2-) - Body ground Always 10 kΩ or higher
      E9-8 (WF1+) - Body ground Always 10 kΩ or higher
      E9-23 (WF1-) - Body ground Always 10 kΩ or higher

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  17

  17. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - BODY GROUND) 
    1. Disconnect the I135 DCM (telematics transceiver) connector.
    2. Disconnect the J5 front No. 2 speaker assembly RH connector.
    3. Measure the resistance between the DCM (telematics transceiver) and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I135-5 (SPO+) - Body ground Always 10 kΩ or higher
      I135-6 (SPO-) - Body ground Always 10 kΩ or higher

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  18

  18. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Remove the DCM (telematics transceiver) (Refer to REMOVAL [10/2014 - ] ).
    2. Measure the resistance according to the value(s) in the table below.
      GTY473616Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher
    3. Proceed to the next step based on the inspection result.

      Result

      Result Proceed to
      NG A
      OK B
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (DCM (Telematics Transceiver))

    Result: 

    A 

    REPLACE DCM (TELEMATICS TRANSCEIVER) 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    B 

    See step  20

  19. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND) 
    1. Disconnect the E9 stereo component amplifier assembly connector.
    2. Disconnect the J5 and K5 front No. 2 speaker assembly connectors.
    3. Disconnect the I84 and I2 front No. 1 speaker assembly connectors.
    4. Disconnect the I60 front No. 3 speaker assembly connector.
    5. Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.
    6. Disconnect the K14 and K15 rear header speaker assembly connectors.
    7. Disconnect the K13 and K16 rear speaker assembly connectors.
    8. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance

      Tester Connection Condition Specified Condition
      E9-12 (TWR+) - Body ground Always 10 kΩ or higher
      E9-27 (TWR-) - Body ground Always 10 kΩ or higher
      E9-11 (TWL+) - Body ground Always 10 kΩ or higher
      E9-26 (TWL-) - Body ground Always 10 kΩ or higher
      E9-15 (FR+) - Body ground Always 10 kΩ or higher
      E9-30 (FR-) - Body ground Always 10 kΩ or higher
      E9-4 (FL+) - Body ground Always 10 kΩ or higher
      E9-19 (FL-) - Body ground Always 10 kΩ or higher
      E9-13 (CTR+) - Body ground Always 10 kΩ or higher
      E9-28 (CTR-) - Body ground Always 10 kΩ or higher
      E9-6 (RR+) - Body ground Always 10 kΩ or higher
      E9-21 (RR-) - Body ground Always 10 kΩ or higher
      E9-5 (RL+) - Body ground Always 10 kΩ or higher
      E9-20 (RL-) - Body ground Always 10 kΩ or higher
      E9-10 (SR+) - Body ground Always 10 kΩ or higher
      E9-25 (SR-) - Body ground Always 10 kΩ or higher
      E9-9 (SL+) - Body ground Always 10 kΩ or higher
      E9-24 (SL-) - Body ground Always 10 kΩ or higher
      E9-7 (WF2+) - Body ground Always 10 kΩ or higher
      E9-22 (WF2-) - Body ground Always 10 kΩ or higher
      E9-8 (WF1+) - Body ground Always 10 kΩ or higher
      E9-23 (WF1-) - Body ground Always 10 kΩ or higher

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  20

  20. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly (Refer to REMOVAL [10/2014 - ] ).
    2. Measure the resistance according to the value(s) in the table below.
      GTY581150Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      FOR LH

      Tester Connection Condition Specified Condition
      3 (TWL-) - 4 (TWL+) Always 10 kΩ or higher
      FOR RH

      Tester Connection Condition Specified Condition
      3 (TWR-) - 4 (TWR+) Always 10 kΩ or higher
      TEXT IN ILLUSTRATION

      *A for RH
      *B for LH
      *a Component without harness connected
      (Front No. 2 Speaker Assembly)

    Result: 

    NG 

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    OK 

    See step  21

  21. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Replace the front No. 2 speaker assembly with a new or known good one (Refer to REMOVAL [10/2014 - ] ).
    2. Clear the DTCs (Refer to DTC CHECK / CLEAR [10/2014 - ] ).
    3. Recheck for DTCs and check that no DTCs are output.

      OK

      No DTCs are output.

      HINT: 

      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
      • Perform the above inspection on both the LH and RH side.

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  22

  22. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 
    1. Remove the front No. 1 speaker assembly (Refer to REMOVAL [10/2014 - ] ).
    2. Measure the resistance according to the value(s) in the table below.
      GTY430134Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 Always 4.6 to 6.6 Ω
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Front No. 1 Speaker Assembly)

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    OK 

    See step  23

  23. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY 
    1. Remove the front No. 3 speaker assembly (Refer to REMOVAL [10/2014 - ] ).
    2. Measure the resistance according to the value(s) in the table below.
      GTY441597Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 Always 6.8 to 10.2 Ω
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Front No. 3 Speaker Assembly)

    Result: 

    NG 

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    OK 

    See step  24

  24. INSPECT REAR NO. 2 SPEAKER ASSEMBLY 
    1. Remove the rear No. 2 speaker assembly (Refer to REMOVAL [10/2014 - ] ).
    2. Measure the resistance according to the value(s) in the table below.
      GTY382828Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      4 - 3 Always 10 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Rear No. 2 Speaker Assembly)

    Result: 

    NG 

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    OK 

    See step  25

  25. REPLACE REAR NO. 2 SPEAKER ASSEMBLY 
    1. Replace the rear No. 2 speaker assembly with a new or known good one (Refer to REMOVAL [10/2014 - ] ).
    2. Clear the DTCs (Refer to DTC CHECK / CLEAR [10/2014 - ] ).
    3. Recheck for DTCs and check that no DTCs are output.

      OK

      No DTCs are output.

      HINT: 

      • Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
      • When there is a possibility that either the right or left rear No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
      • Perform the above inspection on both the LH and RH side.

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  26

  26. INSPECT REAR HEADER SPEAKER ASSEMBLY 
    1. Remove the rear header speaker assembly (Refer to REMOVAL [10/2014 - ] ).
    2. Measure the resistance according to the value(s) in the table below.
      GTY598599Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 Always 4.6 to 6.6 Ω
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Rear Header Speaker Assembly)

    Result: 

    NG 

    REPLACE REAR HEADER SPEAKER ASSEMBLY 

    Result: 

    OK 

    See step  27

  27. INSPECT REAR SPEAKER ASSEMBLY 
    1. Remove the rear speaker assembly (Refer to REMOVAL [10/2014 - ] ).
    2. Measure the resistance according to the value(s) in the table below.
      GTY425847Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 Always 4.8 to 6.8 Ω
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Rear Speaker Assembly)

    Result: 

    OK 

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

scientia non olet · About LEMON Manuals