Customize Parameters [08/2016 - ]

CUSTOMIZE METER / GAUGE SYSTEM

Customizing with the Techstream

Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Utility / Customize / Warning or Display.

Select the setting by referring to the table below.

Warning

Tester Display	Description	Default	Setting	ECU
Key Remind Sound	Function to change the key reminder buzzer sound frequency	Normal	00:Normal, 01:Slow, 10:Fast	Combination meter assembly
Driver Side Seatbelt Warning Buzzer	If the driver side seat belt is unfastened and the vehicle is driven at approximately 20 km/h (12.5 mph) or more, the system sounds the seat belt warning buzzer.	ON	0:OFF, 1:ON	Combination meter assembly
Front Passenger Side Seatbelt Warning Buzzer	If the front passenger side seat belt is unfastened with the front passenger seat occupied, and the vehicle is driven at approximately 20 km/h (12.5 mph) or more, the system sounds the seat belt warning buzzer.	ON	0:OFF, 1:ON	Combination meter assembly
Rear Seatbelt Warning Buzzer	With the ignition switch off, open and close the rear doors, fasten the driver and passenger seat belts and unfasten the rear seat belts. When reaching a speed of 20 km/h (12.5 mph) within 34 seconds of starting the engine the buzzer in the combination meter assembly will sound.	ON	0:OFF, 1:ON	Combination meter assembly
Lane Change Flashing Times Setting	Function to change the lane change flashing time	3	000:OFF, 001:3, 010:4, 011:5, 100:6, 101:7	Combination meter assembly

Display

Tester Display	Description	Default	Setting	ECU
ECO Drive Indicator Zone	Function to enable or disable the eco driving indicator zone display in the multi-information display	OFF	0:OFF, 1:ON	Combination meter assembly
ODO Display Time After IG OFF Setting	Function to change the odometer display time	30s	00:30s, 01:60s, 10:600s, 11:OFF	Combination meter assembly

Customizing with the combination meter assembly

Turn the ignition switch to ON.
Enter the following menus: Settings.

Select the setting by referring to the table below.

NOTE:

Be sure to record the current value before customizing.

SETTINGS

Combination Meter Assembly Display	Description	Default	Setting	ECU
Clock	Function to change the digital clock on the display	24H	12H or 24H	Combination meter assembly
Oil Maintenance	Perform oil maintenance initialization.	-	ON or OFF	Combination meter assembly
Language	Function to change the language on the display	English	English, French or Spanish	Combination meter assembly
Units	Function to change the units on the display	miles (MPG USA)	km (km/L), km (L/100 km), miles (MPG USA) or miles(MPG Imperial)	Combination meter assembly
ECO driving indicator light (Symbol)	Function to activate/deactivate the ECO driving indicator light	ON	ON or OFF	Combination meter assembly
Drive Info	Function to change the item to be displayed on Drive Info 1	Elapsed Time Average Speed	Current Fuel Economy (Bar Type) Average Fuel Economy (After Reset, After Start, After Refuel) Average Speed (After Reset, After Start) Elapsed Time (After Reset, After Start) Distance (Range, After Start) Other (Blank)	Combination meter assembly
Pop-up Display	Function to change the interrupt display setting of each item	-	-	-
Color	Function to change the cursor color when selecting a displayed item	Clear Blue	Clear Blue, Clear Turquoise, Deep Orange or Radiant Orange	Combination meter assembly
Interrupt Display	Function to change the interrupt display setting of each item	ON	ON or OFF	Combination meter assembly
TPMS	Press and hold the steering pad switch assembly to perform initialization.	-	-	Combination meter assembly
Initialization	The setting items can be initialized	-	-	Combination meter assembly

*1: w/ Power Back Door System

*2: w/ Lane Departure Alert System