Pattern Select Switch Sport Mode Circuit [09/2013 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Enter the following menus: System Select / CAN Bus Check.

   Result

   Result	Proceed to
   All of the ECUs and sensors that are currently connected to the CAN communication system are displayed.	A
   None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed.	B

4. Turn the power switch off.

B → See step   10 

A: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Enter the following menus: System Select / Health Check.
4. Check DTCs.
   RESULT
   
   

   Result	Proceed to
   No DTCs are output	A
   DTCs are output	B

5. Turn the power switch off.

B → GO TO DTC CHART 

A: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Enter the following menus: Body Electrical / Combination Meter / Active Test / Indicat. Sport(CVT Sport).
4. Perform the "Indicat. Sport(CVT Sport)" Active Test.

   OK

   The SPORT indicator light blinks.

5. Turn the power switch off.

NG → See step   11 

OK: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Enter the following menus: Powertrain / EV / Data List / Sport Drive Switch.
4. Read the Data List.

   Tester Display	Measurement Item/Range	Normal Condition
   Sport Drive Switch	Sport mode switch condition/ ON or OFF	Sport mode switch being pushed and held: ON Sport mode switch not pushed: OFF

   Result

   Result	Proceed to
   The Techstream display changes according to the sport mode switch operation.	A
   The Techstream display does not change according to the sport mode switch operation.	B

5. Turn the power switch off.

B → See step   5 

A → See step   9 

1. Remove the sport mode switch (pattern select switch). Refer to REMOVAL [09/2013 - ] .
2. Measure the resistance according to the value(s) in the table below.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Standard Resistance

   Tester Connection	Switch Condition	Specified Condition
   6 (MSW1) - 3 (MSW2)	Sport mode switch (pattern select switch) operated	Below 1 Ω
   6 (MSW1) - 3 (MSW2)	Sport mode switch (pattern select switch) not operated	10 kΩ or higher

   TEXT IN ILLUSTRATION
   
   

   *a	Component without harness connected (Sport Mode Switch (Pattern Select Switch))

3. Install the sport mode switch (pattern select switch).

NG → See step   8 

OK: Go to next step 

1. Disconnect connector E127 from the sport mode switch (pattern select switch).
2. Measure the resistance according to the value(s) in the table below.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Standard Resistance

   Tester Connection	Switch Condition	Specified Condition
   E127-3 (MSW2) - Body ground	Power switch off	Below 1 Ω

   TEXT IN ILLUSTRATION
   
   

   *a	Front view of wire harness connector (to Sport Mode Switch (Pattern Select Switch))

3. Connect the sport mode switch (pattern select switch) connector.

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Disconnect connector E118 from the power management control ECU.
2. Disconnect connector E127 from the sport mode switch (pattern select switch).
3. Measure the resistance according to the value(s) in the table below.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Standard Resistance

   Tester Connection	Switch Condition	Specified Condition
   E118-26 (SFTD) - E127-6 (MSW1)	Power switch off	Below 1 Ω
   E118-26 (SFTD) or E127-6 (MSW1) - Body ground	Power switch off	10 kΩ or higher

   TEXT IN ILLUSTRATION
   
   

   *1	Rear view of wire harness connector (to Power Management Control ECU)
   *2	Front view of wire harness connector (to Sport Mode Switch (Pattern Select Switch))

4. Connect the sport mode switch (pattern select switch) connector.
5. Connect the power management control ECU connector.

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → See step   12