Brake Override System [09/2013 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Enter the following menus: System Select / Health Check.
4. Check DTCs.
   RESULT
   
   

   Result	Proceed to
   No DTCs are output	A
   DTCs are output	B

5. Turn the power switch off.

B → GO TO DTC CHART 

A: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Enter the following menus: Powertrain / EV / Data List / Stop Light Switch.
4. Check the Data List indication when the brake pedal is depressed and released.

   OK

   Techstream Display	Condition	Specified Condition
   Stop Light Switch	Brake pedal released	OFF
   	Brake pedal depressed	ON

5. Turn the power switch off.

NG → See step   9 

OK: Go to next step 

1. Inspect and adjust the brake pedal. Refer to ADJUSTMENT [09/2013 - ] .

   HINT: 

   If the stop light switch turns ON too late, the start of brake override system control may be delayed; if it turns ON too soon, brake override system control may begin too early, so conduct an inspection of the brake pedal and stop light switch assembly.

NG → REPAIR OR REPLACE BRAKE PEDAL 

OK: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Enter the following menus: Powertrain / EV / Data List / Accelerator Degree.
4. Read the value displayed on the Techstream.

   OK

   Techstream Display	Condition	Specified Condition
   Accelerator Degree	Accelerator Pedal Released → Depressed → Released	Values smoothly change following accelerator pedal operation

5. Turn the power switch off.

NG → See step   8 

OK: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (READY).
3. Enter the following menus: Powertrain / EV / Data List / Vehicle Spd.
4. Read the value displayed on the Techstream.

   OK

   Techstream Display	Condition	Specified Condition
   Vehicle Spd	Vehicle stopped	0 km/h (0 mph)
   	Vehicle being driven at constant speed between 16.1 to 64.4 km/h (10 to 40 mph)	No large fluctuations when driving at a constant speed

   WARNING:

   When performing the confirmation driving pattern, obey all speed limits and traffic laws.

   HINT: 

   Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.

5. Turn the power switch off.

NG → See step   7 

OK: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (READY).
3. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.
4. Read the value displayed on the Techstream.

   OK

   Techstream Display	Condition	Specified Condition
   FR Wheel Speed FL Wheel Speed RR Wheel Speed RL Wheel Speed	Vehicle stopped	0 km/h (0 mph)
   	Vehicle being driven at constant speed between 16.1 to 64.4 km/h (10 to 40 mph)	No large fluctuations when driving at a constant speed

   WARNING:

   When performing the confirmation driving pattern, obey all speed limits and traffic laws.

   HINT: 

   Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.

5. Turn the power switch off.

NG → INSPECT FRONT OR REAR SPEED SENSOR 

OK → END