LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2014 >> Prius V Three >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge / Display (Diagnostic Codes & Symptom Tests) >> Meter / Gauge System >> On-Vehicle Inspection [08/2013 - ] >> On-Vehicle Inspection [08/2013 - ]

On-Vehicle Inspection [08/2013 - ]

  1. INSPECT COMBINATION METER SUB-ASSEMBLY 
    1. LED INITIAL CHECK
      1. Check the illumination function of the warning or indicator lights listed below when turning the power switch on (IG).

        OK

        Warning or Indicator Specified Condition
        • Water temperature
        • Tire pressure
        • Headlight leveling
        • PCS*1
        • Hybrid system
        • Hybrid system overheat
        • Parking lock system
        • P position request
        • LED headlight*2
        • Eco driving
        • Maintenance required reminder*3
        		 Warning or indicator light comes on for about 3 seconds after turning the power switch on (IG).
        SRS Warning light comes on for about 6 seconds after turning the power switch on (IG).
        • Oil pressure
        • Charge
        • EPS
        • MIL (Check engine warning light)
        		 Indicator or warning light comes on when turning the power switch on (IG) before hybrid system starts.
        • Brake
        • Slip
        • ABS
        • Electronically controlled brake
        		 Indicator or warning light comes on when turning the power switch on (IG) before hybrid system starts.*4
        Indicator or warning light comes on when turn the power switch off to on (READY) for 3 seconds, then goes off.
        • *1: w/ Pre-collision System
        • *2: w/ LED headlight
        • *3: with mph units
        • *4: When turning the power switch on (IG), if it takes 3 seconds or more for the READY indicator light to illuminate, the warning or indicator light turns off right after the READY indicator light illuminates.
    2. Check speedometer operation.
      NOTE:
      • The combination meter sub-assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.
      • The Data List values of the skid control ECU are used for this inspection. Therefore, make sure to perform the inspection after confirming that no DTCs are output from the brake control system.
      • If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform the inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
      1. Before starting the following inspection, check if the brake control system outputs the DTCs.
      2. Check the values by referring to the table below.

        ABS/VSC/TRAC

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        Vehicle Speed Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
        REFERENCE: MPH

        Techstream Indication (mph) Acceptable Range (mph)
        20 19.0 to 21.5
        40 39.1 to 41.9
        60 59.3 to 62.1
        80 79.3 to 82.5
        100 99.5 to 102.7
        120 119.8 to 123
        REFERENCE: KM/H

        Techstream Indication (km/h) Acceptable Range (km/h)
        20 18.2 to 22.2
        40 38.3 to 42.8
        60 58.5 to 63.0
        80 78.4 to 83.4
        100 98.6 to 103.6
        120 118.9 to 123.9
        140 139.1 to 144.1
        160 159.3 to 164.3
        180 179.6 to 184.6
scientia non olet · About LEMON Manuals