LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2014 >> Highlander XLE, FWD >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Supplemental Restraint System - Diagnostic Codes & Circuit Tests - (Except Hybrid) >> Airbag System >> Circuit Tests >> SRS Warning Light Remains ON [12/2013 - 11/2016] >> Procedure

SRS Warning Light Remains ON [12/2013 - 11/2016]: Procedure

  1. CHECK SRS WARNING LIGHT OPERATION 
    1. Turn the ignition switch to ON and check the SRS warning light condition.

      HINT: 

      The primary check is performed for approximately 6 seconds after the ignition switch is turned to ON.

      Result

      Result Proceed to
      After the primary check period, the SRS warning light remains on. A
      After the primary check period, the SRS warning light turns off and turns on again. B

    Result:  2

    B 

    See step  6

    Result:  1

    A 

    See step  2

  2. CHECK BATTERY VOLTAGE 
    1. Measure the voltage of the battery.

      Standard Voltage

      11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    INSPECT CHARGING SYSTEM AND BATTERY 

    for 1AR-FE: Refer to ON-VEHICLE INSPECTION [12/2013 - ]

    for 2GR-FE: Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016]

    Result:  1

    OK 

    See step  3

  3. CHECK CONNECTOR 
    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connector is properly connected to the airbag sensor assembly.

      OK

      The connector is properly connected.

      HINT: 

      If the connector is not properly connected, reconnect the connector and proceed to the next inspection.

    4. Disconnect the connector from the airbag sensor assembly.
    5. Check that the terminals of the connector are not damaged.

      OK

      The terminals are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPLACE WIRE HARNESS 

    Result:  1

    OK 

    See step  4

  4. CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND) 
    1. Connect the cable to the negative (-) battery terminal.
      GTY439989Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Airbag Sensor Assembly)
    2. Turn the ignition switch to ON.
    3. Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      F38-21 (IG2) - Body ground Ignition switch ON 8 to 16 V
    5. Turn the ignition switch off.
    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F38-25 (E1) - Body ground Always Below 1 Ω
      F38-26 (E2) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPLACE WIRE HARNESS 

    Result:  1

    OK 

    See step  5

  5. CHECK SRS WARNING LIGHT 
    1. Turn the ignition switch to ON and check the SRS warning light condition.

      OK

      After the primary check period, the SRS warning light goes off for approximately 10 seconds and turns back on.

      HINT: 

      The primary check period is approximately 6 seconds after the ignition switch is turned to ON.

      Result

      Proceed to
      OK
      NG

    Result:  1

    OK 

    REPLACE AIRBAG SENSOR ASSEMBLY. Refer to  REMOVAL [12/2013 - ] 

    Result:  2

    NG 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [12/2013 - ] 

  6. CHECK CAN COMMUNICATION SYSTEM 
    1. Using the Techstream, check if the CAN communication system is functioning normally.

      OK

      CAN communication system is functioning normally.

      HINT: 

      • Refer to CAN Bus Check for the CAN communication system.

        Refer to DIAGNOSIS SYSTEM [12/2013 - 11/2016]

      • The airbag sensor assembly is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there are no malfunctions in the CAN communication system.

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016] 

    Result:  1

    OK 

    See step  7

  7. CHECK BATTERY VOLTAGE 
    1. Measure the voltage of the battery.

      Standard Voltage

      11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    INSPECT CHARGING SYSTEM AND BATTERY 

    for 1AR-FE: Refer to ON-VEHICLE INSPECTION [12/2013 - ]

    for 2GR-FE: Refer to ON-VEHICLE INSPECTION [12/2013 - 11/2016]

    Result:  1

    OK 

    See step  8

  8. CHECK CONNECTOR 
    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connector is properly connected to the airbag sensor assembly.

      OK

      The connector is properly connected.

      HINT: 

      If the connector is not properly connected, reconnect the connector and proceed to the next inspection.

    4. Disconnect the connector from the airbag sensor assembly.
    5. Check that the terminals of the connector are not damaged.

      OK

      The terminals are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPLACE WIRE HARNESS 

    Result:  1

    OK 

    See step  9

  9. CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND) 
    1. Connect the cable to the negative (-) battery terminal.
      GTY439989Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Airbag Sensor Assembly)
    2. Turn the ignition switch to ON.
    3. Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      F38-21 (IG2) - Body ground Ignition switch ON 8 to 16 V
    5. Turn the ignition switch off.
    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F38-25 (E1) - Body ground Always Below 1 Ω
      F38-26 (E2) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPLACE WIRE HARNESS 

    Result:  1

    OK 

    See step  10

  10. CHECK CONNECTOR 
    1. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    2. Check that the connector is properly connected to the combination meter assembly.

      OK

      The connector is properly connected.

      HINT: 

      If the connector is not properly connected, reconnect the connector and proceed to the next inspection.

    3. Disconnect the connector from the combination meter assembly.
    4. Check that the terminals of the connector are not damaged.

      OK

      The terminals are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPAIR OR REPLACE CONNECTOR 

    Result:  1

    OK 

    See step  11

  11. CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND) 
    1. Connect the cable to the negative (-) battery terminal.
      GTY442494Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Combination Meter Assembly)
    2. Turn the ignition switch to ON.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      F22-13 (IG+) - Body ground Ignition switch ON 11 to 14 V
      F22-1 (B) - Body ground Always 11 to 14 V
    4. Turn the ignition switch off.
    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F22-20 (ES) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPAIR OR REPLACE WIRE HARNESS 

    Result:  1

    OK 

    See step  12

  12. CHECK SRS WARNING LIGHT 
    1. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    2. Connect the connector to the combination meter assembly.
    3. Connect the cable to the negative (-) battery terminal.
    4. Turn the ignition switch to ON and check the SRS warning light condition.

      OK

      After the primary check period, the SRS warning light goes off for approximately 10 seconds and turns back on.

      HINT: 

      The primary check period is approximately 6 seconds after the ignition switch is turned to ON.

      Result

      Proceed to
      OK
      NG

    Result:  1

    OK 

    REPLACE AIRBAG SENSOR ASSEMBLY. Refer to  REMOVAL [12/2013 - ] 

    Result:  2

    NG 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [12/2013 - ] 

scientia non olet · About LEMON Manuals