LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2014 >> Highlander XLE, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 55 (Automatic Transmission (UA80E) - Diagnostic Codes (3 Of 3) & Circuit Tests) >> Automatic Transaxle System >> DTC P0740-15: Torque Converter Clutch Circuit Short to Battery or Open [10/2017 - ] >> Procedure

DTC P0740-15: Torque Converter Clutch Circuit Short to Battery or Open [10/2017 - ]: Procedure

WARNING: This page is about a different car, the 2019 Toyota Highlander, 2018 Toyota Highlander, and 2017 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT TRANSMISSION WIRE (SOLENOID (SL) VALVE) 
    1. Disconnect the C92 transmission wire connector.
      GTY730445Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Transmission Wire)
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      13 (SL) - Body ground 20°C (68°F) 11 to 15 Ω
      13 (SL) - Other terminals Always 10 kΩ or higher
    3. Connect the C92 transmission wire connector.

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    See step  4

    Result:  1

    OK 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) 
    1. Disconnect the C1 ECM connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C1-62 (SL) - Body ground 20°C (68°F) 11 to 15 Ω
      C1-62 (SL) - Other terminals Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM) 

    Result:  1

    OK 

    See step  3

  3. REPLACE ECM 
    1. Replace the ECM.

      Refer to COMPONENTS [11/2016 - ]

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    PERFORM REGISTRATION. Refer to  REGISTRATION [11/2016 - ] 

  4. INSPECT SOLENOID (SL) VALVE 
    1. Remove the solenoid (SL) valve.
      GTY720881Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Solenoid (SL) Valve

      Refer to DISASSEMBLY [11/2016 - ]

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      Solenoid (SL) valve connector terminal - Solenoid (SL) valve body 20°C (68°F) 11 to 15 Ω
    3. Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

      OK

      Valve moves and makes an operating sound.

      Result

      Proceed to
      OK
      NG

    Result:  1

    OK 

    REPAIR OR REPLACE TRANSMISSION WIRE. Refer to  COMPONENTS [11/2016 - ] 

    Result:  2

    NG 

    REPLACE SOLENOID (SL) VALVE. Refer to  COMPONENTS [11/2016 - ] 

scientia non olet · About LEMON Manuals