DTC P0715: Input / Turbine Speed Sensor Circuit Malfunction; DTC P0717: Input Speed Sensor Circuit No Signal [12/2013 - 08/2014]: Procedure

1. Remove the valve body assembly.
2. Make sure that the connector is properly connected, and check the speed sensor installation.

   Refer to INSTALLATION [12/2013 - 11/2016]

   OK

   The installation bolts are tightened properly and there is no clearance between the sensor and valve body assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

REPAIR OR REPLACE TRANSMISSION REVOLUTION SENSOR. Refer to  COMPONENTS [12/2013 - ] 

Result:  1

OK 

See step  2

1. Disconnect the speed sensor connector from the transmission wire.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component without harness connected (Transmission Wire)
   *b	Wiring harness connector side
   *c	Sensor side

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   1 (NTB) sensor side - A-1 (NTB) wiring harness connector side	Always	Below 1 Ω
   2 (NTO) sensor side - A-2 (NTO) wiring harness connector side	Always	Below 1 Ω
   1 (NTB) sensor side - Body ground and other terminals	Always	10 kΩ or higher
   2 (NTO) sensor side - Body ground and other terminals	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

REPLACE TRANSMISSION WIRE. Refer to  COMPONENTS [12/2013 - ] 

Result:  1

OK 

See step  3

1. Disconnect the ECM connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   C2-1 (NTB) - C1-116 (NTB)	Always	Below 1 Ω
   C2-2 (NTO) - C1-115 (NTO)	Always	Below 1 Ω
   C2-1 (NTB) or C1-116 (NTB) - Body ground and other terminals	Always	10 kΩ or higher
   C2-2 (NTO) or C1-115 (NTO) - Body ground and other terminals	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result:  1

OK 

See step  4

1. Remove the wiring harness connector.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component without harness connected (Wiring Harness Connector)	*b	ECM side
   *c	Transmission wire side	-	-

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   C2-1 (NTB) - A-1 (NTB)	Always	Below 1 Ω
   C2-2 (NTO) - A-2 (NTO)	Always	Below 1 Ω
   C2-1 (NTB) - All other terminals	Always	10 kΩ or higher
   C2-2 (NTO) - All other terminals	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

REPLACE WIRING HARNESS CONNECTOR. Refer to  COMPONENTS [12/2013 - 11/2016] 

Result:  1

OK 

See step  5

Refer to COMPONENTS [12/2013 - ]

Result

Result:  1

NEXT 

See step  6

1. Connect the Techstream to the DLC3.
2. Start the engine and turn the Techstream on.
3. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [12/2013 - ]

   HINT: 

   Write down the currently output DTCs before clearing them.

4. Perform the monitor drive pattern.

   Refer to MONITOR DRIVE PATTERN [12/2013 - ]

5. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

   Powertrain > Engine > Trouble Codes 

6. Read the DTCs using the Techstream.

   Result

   Result	Proceed to
   Only DTC P0715 or P0717 is output	A
   DTCs are not output	B

Result:  1

A 

REPLACE ECM. Refer to  COMPONENTS [12/2013 - 11/2016] 

Result:  2

B 

END