Replacement [12/2013 - ]: Procedure

Refer to PROCEDURE - Step 8 , or refer to PROCEDURE - Step 8

Refer to PROCEDURE - Step 11 , or refer to PROCEDURE - Step 11

Refer to PROCEDURE - Step 13 , or refer to PROCEDURE - Step 13

1. Remove the refill plug and gasket from the automatic transaxle assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

3. Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	No. 1 Transmission Oil Filler Tube
   *a	Hexagon Socket Wrench
   *b	Overflow Plug Hole

4. Drain the automatic transaxle fluid from the automatic transaxle assembly.
5. Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	No. 1 Transmission Oil Filler Tube
   *a	Hexagon Socket Wrench
   *b	Overflow Plug Hole

   Torque: 0.8 N*m (8 kgf*cm, 7 in.*lbf) 

6. Using a 6 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the automatic transaxle oil pan sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   HINT: 

   Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.

7. Temporarily install the gasket and refill plug to the automatic transaxle assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   HINT: 

   Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.

Refer to REMOVAL [12/2013 - ]

Refer to PROCEDURE - Step 73 , or refer to PROCEDURE - Step 73

1. Using SST, remove the front drive shaft oil seal LH from the automatic transaxle assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   • SST: 09308-00010 
   NOTE:

   Be careful not to damage the transaxle case sub-assembly.

1. Using SST, remove the front drive shaft oil seal RH from the automatic transaxle assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   • SST: 09308-00010 
   NOTE:

   Be careful not to damage the transaxle housing.

1. Using SST and a hammer, install a new front drive shaft oil seal LH to the automatic transaxle assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   • SST: 09316-10010 
   • SST: 09950-70010 
     1. 09951-07100

   Standard Depth

   -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

   NOTE:

   • Make sure that the front drive shaft oil seal LH is installed in the correct direction.
   • Do not damage the front drive shaft oil seal LH lip.
2. Coat the lip of the front drive shaft oil seal LH with MP grease.

1. Using SST and a hammer, install a new front drive shaft oil seal RH to the automatic transaxle assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   • SST: 09316-60011 
     1. 09316-00011

   Standard Depth

   -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

   NOTE:

   • Make sure that the front drive shaft oil seal RH is installed in the correct direction.
   • Do not damage the front drive shaft oil seal RH lip.
2. Coat the lip of the front drive shaft oil seal RH with MP grease.

Refer to PROCEDURE - Step 6 , or refer to PROCEDURE - Step 6

Refer to INSTALLATION [12/2013 - ]

Refer to ADJUSTMENT [12/2013 - 11/2016] , or refer to ADJUSTMENT [11/2016 - ] 

Refer to PROCEDURE - Step 75 , or refer to PROCEDURE - Step 75

Refer to PROCEDURE - Step 77 , or refer to PROCEDURE - Step 77

Refer to PROCEDURE - Step 81 , or refer to PROCEDURE - Step 81