LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2014 >> Highlander XLE, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 3 (Engine Control System (2GR-FKS) (Service Information) (Except Hybrid)) >> Camshaft Position Sensor >> Installation [11/2016 - ] >> Procedure

Installation [11/2016 - ]: Procedure

WARNING: This page is about a different car, the 2019 Toyota Highlander, 2018 Toyota Highlander, and 2017 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL VVT SENSOR (for Exhaust Side of Bank 2) 
    1. Apply a light coat of engine oil to the O-ring of the VVT sensor.
      NOTE:

      If reusing the VVT sensor, be sure to inspect the O-ring.

    2. Clean the bolt and bolt hole.
    3. Apply adhesive to 2 or 3 threads at the end of the bolt.
      GTY445334Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Adhesive

      Adhesive

      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    4. Install the VVT sensor to the cylinder head cover sub-assembly LH with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • If the VVT sensor has been struck or dropped, replace it.
      • Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.
    5. Connect the VVT sensor connector.
  2. INSTALL VVT SENSOR (for Intake Side of Bank 2) 
    1. Apply a light coat of engine oil to the O-ring of the VVT sensor.
      NOTE:

      If reusing the VVT sensor, be sure to inspect the O-ring.

    2. Clean the bolt and bolt hole.
    3. Apply adhesive to 2 or 3 threads at the end of the bolt.
      GTY445334Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Adhesive

      Adhesive

      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    4. Install the VVT sensor to the cylinder head cover sub-assembly LH with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • If the VVT sensor has been struck or dropped, replace it.
      • Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.
    5. Connect the VVT sensor connector.
  3. INSTALL VVT SENSOR (for Exhaust Side of Bank 1) 
    1. Apply a light coat of engine oil to the O-ring of the VVT sensor.
      NOTE:

      If reusing the VVT sensor, be sure to inspect the O-ring.

    2. Clean the bolt and bolt hole.
    3. Apply adhesive to 2 or 3 threads at the end of the bolt.
      GTY445334Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Adhesive

      Adhesive

      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    4. Install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • If the VVT sensor has been struck or dropped, replace it.
      • Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.
    5. Connect the VVT sensor connector.
  4. INSTALL VVT SENSOR (for Intake Side of Bank 1) 
    1. Apply a light coat of engine oil to the O-ring of the VVT sensor.
      NOTE:

      If reusing the VVT sensor, be sure to inspect the O-ring.

    2. Clean the bolt and bolt hole.
    3. Apply adhesive to 2 or 3 threads at the end of the bolt.
      GTY445334Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Adhesive

      Adhesive

      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    4. Install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • If the VVT sensor has been struck or dropped, replace it.
      • Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.
    5. Connect the VVT sensor connector.
  5. INSTALL INTAKE AIR SURGE TANK ASSEMBLY 

    Refer to INSTALLATION [11/2016 - ]

  6. INSPECT FOR ENGINE OIL LEAK 

    Refer to PROCEDURE - Step 5

scientia non olet · About LEMON Manuals