LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2014 >> Highlander XLE, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 11 (Automatic Transmission (UA80E) - Service Information (1 Of 2)) >> Shift Lever >> Inspection [11/2016 - ] >> Procedure

Inspection [11/2016 - ]: Procedure

WARNING: This page is about a different car, the 2019 Toyota Highlander, 2018 Toyota Highlander, and 2017 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (w/o Smart Key System) 

    HINT: 

    If the results of the following inspections are as specified but a malfunction has occurred, replace the transmission floor shift assembly.

    1. Inspect wire harness:
      1. Disconnect the shift lock control ECU connector.
        GTY449985Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Measure the voltage according to the value(s) in the table below.
        GTY541572Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Front view of wire harness connector
        (to Shift Lock Control ECU)

        Standard Voltage

        Tester Connection Condition Specified Condition
        6 (ACC) - Body ground Ignition switch ACC 11 to 14 V
        Ignition switch off Below 1 V
        4 (STP) - Body ground Brake pedal depressed 11 to 14 V
        Brake pedal released Below 1 V
        8 (IG) - Body ground Ignition switch ON 11 to 14 V
        Ignition switch off Below 1 V

        If the result is not as specified, repair or replace the shift lock control ECU wire harness.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Value
        1 (E) - Body ground Always Below 1 Ω
        GTY428231Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Front view of wire harness connector
        (to Shift Lock Control ECU)

        If the result is not as specified, repair or replace the shift lock control ECU wire harness.

    2. Inspect key interlock solenoid operation signal:
      1. Connect the shift lock control ECU connector.
        GTY449985Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Measure the voltage according to the value(s) in the table below.
        GTY492874Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component with harness connected
        (Shift Lock Control ECU)

        Standard Voltage

        Tester Connection Condition Specified Condition
        5 (KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
        Ignition switch ACC and shift lever not in P 11 to 14 V

        HINT: 

        Do not disconnect the shift lock control ECU connector.

        If the result is not as specified, repair or replace the transmission floor shift assembly.

    3. Inspect shift lock solenoid:
      1. Disengage the 3 claws to remove the shift lock control ECU from the transmission floor shift assembly.
        GTY449983Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Disconnect the shift lock solenoid connector.
        GTY449990Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Measure the resistance according to the value(s) in the table below.
        GTY455050Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Front view of wire harness connector
        (to Shift Lock Solenoid)

        Standard Resistance

        Tester Connection Condition Specified Condition
        4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
        Shift lever not in P Below 1 Ω

        If the result is not as specified, replace the transmission floor shift assembly.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        1 (SLS+) - 2 (SLS-) Always 112 Ω

        If the result is not as specified, replace the transmission floor shift assembly.

  2. INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (w/ Smart Key System) 

    HINT: 

    If the results of the following inspections are as specified but a malfunction has occurred, replace the transmission floor shift assembly.

    1. Inspect wire harness:
      1. Disconnect the shift lock control ECU connector.
        GTY449985Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Measure the voltage according to the value(s) in the table below.
        GTY435431Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Front view of wire harness connector
        (to Shift Lock Control ECU)

        Standard Voltage

        Tester Connection Condition Specified Condition
        6 (STP) - Body ground Brake pedal depressed 11 to 14 V
        Brake pedal released Below 1 V
        12 (IG) - Body ground Engine switch on (IG) 11 to 14 V
        Engine switch off Below 1 V

        If the result is not as specified, repair or replace the shift lock control ECU wire harness.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Value
        3 (E) - Body ground Always Below 1 Ω
        GTY452934Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Front view of wire harness connector
        (to Shift Lock Control ECU)

        If the result is not as specified, repair or replace the shift lock control ECU wire harness.

    2. Inspect shift lock solenoid:
      1. Disengage the 3 claws to remove the shift lock control ECU from the transmission floor shift assembly.
        GTY449983Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Disconnect the shift lock solenoid connector.
        GTY449990Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Measure the resistance according to the value(s) in the table below.
        GTY455050Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Front view of wire harness connector
        (to Shift Lock Solenoid)

        Standard Resistance

        Tester Connection Condition Specified Condition
        4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
        Shift lever not in P Below 1 Ω

        If the result is not as specified, replace the transmission floor shift assembly.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        1 (SLS+) - 2 (SLS-) Always 112 Ω

        If the result is not as specified, replace the transmission floor shift assembly.

  3. INSPECT TRANSMISSION CONTROL SWITCH 
    1. Disconnect the transmission control switch connector.
      GTY449984Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.
      GTY428230Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Transmission Control Switch)

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
      Shift lever not in S, "+" or "-" 10 kΩ or higher
      2 (SFTU) - 5 (E) Shift lever held in "+" Below 1 Ω
      Shift lever not held in "+" 10 kΩ or higher
      1 (SFTD) - 5 (E) Shift lever held in "-" Below 1 Ω
      Shift lever not held in "-" 10 kΩ or higher

      If the result is not as specified, replace the transmission floor shift assembly.

scientia non olet · About LEMON Manuals