LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2014 >> Highlander XLE, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 11 (Automatic Transmission (UA80E) - Service Information (1 Of 2)) >> Automatic Transaxle Fluid >> Replacement [11/2016 - ] >> Procedure

Replacement [11/2016 - ]: Procedure

WARNING: This page is about a different car, the 2019 Toyota Highlander, 2018 Toyota Highlander, and 2017 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 8

  2. REMOVE FRONT FENDER APRON SEAL LH 

    Refer to PROCEDURE - Step 13

  3. REPLACE AUTOMATIC TRANSAXLE FLUID 
    1. Lift the vehicle. [#1]
      NOTE:

      Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the tilt angle from the front to rear and side to side of the vehicle is within +/- 1°).

    2. Remove the refill plug and gasket from the automatic transaxle case sub-assembly. [#2]
      GTY693071Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing. [#3]
      GTY694221Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid. [#4]
      GTY704916Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 1 Transmission Oil Filler Tube
    5. Measure the amount of automatic transaxle fluid drained. [#5]
      GTY706326Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Add the same amount of automatic transaxle fluid in step [#8].

    6. Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing. [#6]

      Torque: 1.7 N*m (17 kgf*cm, 15 in.*lbf) 

    7. Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing. [#7]
      GTY694221Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.

    8. Add automatic transaxle fluid to the refill hole using the same amount of automatic transaxle fluid drained in step [#5]. [#8]
      GTY706325Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Use Toyota Genuine ATF WS.

    9. Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage. [#9]
      GTY693071Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.

    10. Lower the vehicle. [#10]
    11. Start the engine. [#11]
    12. Slowly move the shift lever from P to D, and then back to P. [#12]

      HINT: 

      • Slowly move the shift lever to circulate the automatic transaxle fluid through each part of the automatic transaxle assembly.
      • Keep the shift lever in each position for approximately 3 seconds.
    13. Allow the engine to idle for 30 seconds to warm it up. [#13]
    14. Turn the ignition switch off. [#14]
    15. Repeat steps [#1] to [#14].
    16. Repeat steps [#1] to [#10].
  4. ADD SPECIFIED AMOUNT OF AUTOMATIC TRANSAXLE FLUID 

    See step  5

  5. ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Using the Techstream) 

    See step  6

  6. ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Not Using the Techstream) 

    See step  7

  7. ADJUST AUTOMATIC TRANSAXLE FLUID LEVEL 

    See step  8

  8. REBUILD WORK 

    See step  9

  9. INSTALL FRONT FENDER APRON SEAL LH 

    Refer to PROCEDURE - Step 97

  10. INSTALL NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 103

scientia non olet · About LEMON Manuals