LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2014 >> Highlander XLE, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 10 (Starting System (W/O Stop And Start) [2GR-FKS] - Service Information - (Except Hybrid)) >> STARTER (w/o Stop And Start System) >> Reassembly [11/2016 - ] >> Procedure

Reassembly [11/2016 - ]: Procedure

WARNING: This page is about a different car, the 2019 Toyota Highlander, 2018 Toyota Highlander, and 2017 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL PLANETARY GEAR 
    1. Apply high-temperature grease to the 3 planetary gears, 3 planetary gear shafts and starter drive housing assembly.
      GTY443526Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      High-temperature Grease
    2. Install the 3 planetary gears to the starter drive housing assembly.
  2. INSTALL STARTER ARMATURE ASSEMBLY 
    1. Secure the starter commutator end frame assembly in a vise between aluminum plates.
      NOTE:

      Do not overtighten the vise.

    2. Apply high-temperature grease to the starter armature shaft.
      GTY442069Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      High-temperature Grease
    3. Apply high-temperature grease to the washer and bearing shown in the illustration.
      GTY430882Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      High-temperature Grease
    4. Install the starter armature assembly to the starter commutator end frame assembly.
    5. Using snap ring pliers, install the washer and a new snap ring.
      NOTE:
      • Be sure to install the snap ring in the starter armature shaft groove securely.
      • Do not expand the snap ring excessively.
      GTY458197Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Snap Ring Pliers
    6. Using a vernier caliper, measure the width of the snap ring end gap as shown in the illustration.
      GTY436451Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Width

      Maximum Width

      5.0 mm (0.197 in.)

      If the width is greater than the maximum, replace the snap ring with a new one.

  3. INSTALL STARTER COMMUTATOR END FRAME COVER 
    1. Install the starter commutator end frame cover to the starter commutator end frame assembly.
      GTY191557Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL STARTER ARMATURE PLATE 
    1. Insert the starter armature plate to the starter yoke assembly.
      GTY727052Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Keyway
      *b Key
    2. Align the keyway of the starter armature plate with the key inside the starter yoke assembly, and install the starter armature plate.
  5. INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY 
    GTY728458Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Rubber
    *b Cutout
    1. Align the rubber of the starter commutator end frame assembly with the cutout of the starter yoke assembly.
    2. Install the starter commutator end frame assembly to the starter yoke assembly.
      NOTE:

      The magnet of the starter yoke assembly may attract the starter armature assembly when the starter commutator end frame assembly is installed, causing the magnet to break.

  6. INSTALL STARTER YOKE ASSEMBLY 
    1. Align the protrusion of the starter yoke assembly with the cutout of the starter drive housing assembly.
      GTY449129Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protrusion
      *b Cutout
    2. Install the starter yoke assembly with the 2 through bolts.

      Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) 

  7. INSTALL REPAIR SERVICE STARTER KIT 
    1. Apply high-temperature grease to the plunger.
      GTY452974Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Hook
      High-temperature Grease
    2. Hang the hook of the plunger on the drive lever.
    3. Apply high-temperature grease to the return spring.
      GTY431398Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      High-temperature Grease
    4. Install the return spring to the plunger.
    5. Install the magnet switch to the starter drive housing assembly with the 2 screws.

      Torque: 7.5 N*m (76 kgf*cm, 66 in.*lbf) 

    6. Connect the field coil lead wire to terminal C with the nut.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

scientia non olet · About LEMON Manuals