LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2014 >> Highlander LE Plus, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 67 (Seat Belts (Service Information) (Hybrid)) >> Rear No. 2 Seat Outer Belt Assembly >> Installation [02/2014 - 11/2015] >> Procedure

Installation [02/2014 - 11/2015]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY 
    1. Temporarily install the rear No. 2 seat outer belt assembly with the 2 bolts.
      Fig 1: Tightening Sequence Of Rear No. 2 Seat Outer Belt Assembly
      GTY427786Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Fully tighten the bolt (A) first, then the bolt (B).

      Bolt (A) 

      Torque: 7.5 N*m (76 kgf*cm, 66 in.*lbf) 

      Bolt (B) 

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

    3. Connect the shoulder anchor of the rear No. 2 seat outer belt assembly with the bolt.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

  2. INSTALL INNER ROOF SIDE GARNISH ASSEMBLY 

    Refer to PROCEDURE - Step 22

  3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side) 

    Refer to PROCEDURE - Step 24

  4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side) 

    Refer to PROCEDURE - Step 35

  5. INSTALL ROPE HOOK 

    Refer to PROCEDURE - Step 25

  6. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK 

    Refer to PROCEDURE - Step 26

  7. INSTALL DECK TRIM POCKET COVER 

    Refer to PROCEDURE - Step 27

  8. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (for RH Side) 

    Refer to PROCEDURE - Step 2

  9. INSTALL COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR (for RH Side) 

    Refer to PROCEDURE - Step 1

  10. CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY 
    1. Connect the floor anchor of the rear No. 2 seat outer belt assembly with the bolt.
      GTY443156Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Protruding Part

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

      NOTE:

      Do not allow the anchor part of the rear No. 2 seat outer belt assembly to overlap the protruding part of the floor panel.

  11. INSTALL NO. 2 DECK SIDE TRIM COVER (for LH Side) 

    Refer to PROCEDURE - Step 30

  12. INSTALL NO. 1 DECK SIDE TRIM COVER (for RH Side) 

    Refer to PROCEDURE - Step 43

  13. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY 

    See step  13

  14. INSTALL FRONT DECK SIDE TRIM COVER 

    Refer to PROCEDURE - Step 32

  15. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP 

    Refer to PROCEDURE - Step 49

  16. INSTALL REAR DOOR SCUFF PLATE LH (for LH Side) 

    Refer to PROCEDURE - Step 50

  17. INSTALL REAR DOOR SCUFF PANEL LH (for LH Side) 

    Refer to PROCEDURE - Step 51

  18. INSTALL REAR DOOR SCUFF PLATE RH (for RH Side) 

    HINT: 

    Use the same procedure as for the LH side.

    Refer to PROCEDURE - Step 50

  19. INSTALL REAR OUTER SEAT TRACK BRACKET COVER 

    Refer to PROCEDURE - Step 5

  20. INSTALL REAR NO. 2 SEAT ASSEMBLY 

    Refer to INSTALLATION [02/2014 - 11/2016]

  21. INSTALL REAR FLOOR FINISH PLATE 

    Refer to PROCEDURE - Step 68

  22. INSTALL REAR DECK FLOOR BOX 

    Refer to PROCEDURE - Step 69

  23. INSTALL DECK SIDE TRIM BOX LH 

    Refer to PROCEDURE - Step 70

  24. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 71

  25. INSTALL DECK BOARD ASSEMBLY 

    Refer to PROCEDURE - Step 72

scientia non olet · About LEMON Manuals