Installation [02/2014 - 11/2016]: Procedure

WARNING: This page is about a different variant/trim than selected.

INSTALL FRONT SEAT OUTER BELT ASSEMBLY

Temporarily install the front seat outer belt assembly with the 2 bolts.

Fig 2: Tightening Sequence Of Front Seat Outer Belt Assembly
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Fully tighten the bolt (A) first, then the bolt (B).
Bolt (A)

Torque: 7.5 N*m (76 kgf*cm, 66 in.*lbf)

Bolt (B)

Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)

for LH Side:

Connect the pretensioner connector and lock the locking button as shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Locking Button
*b	Lock

NOTE:

Securely lock the locking button.

for RH Side:

Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTE:

Securely lock the locking button.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Locking Button
*b	Lock
*c	Pretensioner Connector
*d	Selectable Force Limiter Connector

Connect the selectable force limiter connector and lock the locking button as shown in the illustration.
NOTE:
Securely lock the locking button.

Connect the shoulder anchor of the front seat outer belt assembly with the nut.
Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
Check that the ELR locks.
NOTE:
The check should be performed with the front seat outer belt assembly installed.
1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

INSTALL CENTER PILLAR GARNISH
Refer to PROCEDURE - Step 46 , or refer to PROCEDURE - Step 47

CONNECT FRONT SEAT OUTER BELT ASSEMBLY

Connect the floor anchor of the front seat outer belt assembly with the bolt.

Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)

INSTALL LOWER CENTER PILLAR GARNISH
Refer to PROCEDURE - Step 48 , or refer to PROCEDURE - Step 49
CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
Refer to PROCEDURE - Step 49 , or refer to PROCEDURE - Step 50
INSTALL REAR DOOR SCUFF PLATE LH (for LH Side)
Refer to PROCEDURE - Step 50 , or refer to PROCEDURE - Step 51
INSTALL REAR DOOR SCUFF PANEL LH (for LH Side)
Refer to PROCEDURE - Step 51 , or refer to PROCEDURE - Step 52
INSTALL REAR DOOR SCUFF PLATE RH (for RH Side)
HINT:

Use the same procedure as for the LH side.

Refer to PROCEDURE - Step 50 , or refer to PROCEDURE - Step 51
INSTALL REAR OUTER SEAT TRACK BRACKET COVER
Refer to PROCEDURE - Step 5
CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
Refer to PROCEDURE - Step 54 , or refer to PROCEDURE - Step 55
INSTALL FRONT DOOR SCUFF PLATE
Refer to PROCEDURE - Step 56 , or refer to PROCEDURE - Step 57
CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
NOTE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Refer to INITIALIZATION [02/2014 - 11/2016]
INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY
Refer to PROCEDURE - Step 71 , or refer to PROCEDURE - Step 72
INSTALL DECK BOARD ASSEMBLY
Refer to PROCEDURE - Step 72 , or refer to PROCEDURE - Step 73
INSPECT SRS WARNING LIGHT
Refer to DIAGNOSIS SYSTEM [02/2014 - ]