LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2014 >> Camry LE >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 176 (Supplemental Restraint System (Diagnostic Codes (B1627/82 - B1813/53)) (Hybrid)) >> Airbag System >> DTC B1660/43: Passenger Airbag ON/OFF Indicator Circuit Malfunction [08/2013 - 12/2013] >> Procedure

DTC B1660/43: Passenger Airbag ON/OFF Indicator Circuit Malfunction [08/2013 - 12/2013]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION 
    1. Turn the power switch on (IG).
    2. Check the passenger airbag ON/OFF indicator operation.

      Result

      ON/OFF Indicator Illumination Proceed to
      Always ON A
      OFF B

      HINT: 

      Refer to the normal condition of the passenger airbag ON/OFF indicator. Refer to DIAGNOSIS SYSTEM [08/2013 - ] .

    B → See step   9 

    A: Go to next step 

  2. CHECK CONNECTORS 
    1. Turn the power switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly and air conditioning control assembly.

      OK

      The connectors are properly connected.

      HINT: 

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly and air conditioning control assembly.
    5. Check that the terminals of the connectors are not damaged.

      OK

      The terminals are not deformed or damaged.

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK: Go to next step 

  3. CHECK PASSENGER AIRBAG ON/OFF INDICATOR 
    1. Connect the connector to the air conditioning control assembly.
    2. Connect the cable to the negative (-) auxiliary battery terminal.
    3. Turn the power switch on (IG).
    4. Check the passenger airbag ON/OFF indicator operation.

      OK

      The passenger airbag ON/OFF indicator does not come on.

    NG → See step   5 

    OK: Go to next step 

  4. CHECK DTC 
    1. Turn the power switch off.
      GTY315873Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Connect the connector to the airbag sensor assembly.
    4. Connect the cable to the negative (-) auxiliary battery terminal.
    5. Clear the DTCs stored in memory. Refer to DTC CHECK / CLEAR [08/2013 - ] .
    6. Turn the power switch off.
    7. Turn the power switch on (IG), and wait for at least 60 seconds.
    8. Check for DTCs. Refer to DTC CHECK / CLEAR [08/2013 - ] .

      OK

      DTC B1660/43 is not output.

      HINT: 

      Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.

      TEXT IN ILLUSTRATION

      *1 Air Conditioning Control Assembly
      *2 Airbag Sensor Assembly

    NG → See step   17 

    OK → See step   19 

  5. CHECK INSTRUMENT PANEL WIRE (OPEN) 
    1. Turn the power switch off.
      GTY425520Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Disconnect the connector from the air conditioning control assembly.
    4. Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I56-8 (PAON) - I56-16 (P-AB) Always Below 1 Ω
    6. Disconnect the service wire from connector B.
      TEXT IN ILLUSTRATION

      *1 Air Conditioning Control Assembly
      *2 Airbag Sensor Assembly
      *3 Instrument Panel Wire
      *4 Service Wire
      *a Front view of wire harness connector
      (to Airbag Sensor Assembly)
      *b Front view of wire harness connector
      (to Air Conditioning Control Assembly)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK: Go to next step 

  6. CHECK INSTRUMENT PANEL WIRE (SHORT) 
    GTY441734Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I56-8 (PAON) - I56-16 (P-AB) Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Air Conditioning Control Assembly
      *2 Airbag Sensor Assembly
      *3 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Air Conditioning Control Assembly)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK: Go to next step 

  7. CHECK INSTRUMENT PANEL WIRE (SHORT TO B+) 
    1. Connect the cable to the negative (-) auxiliary battery terminal.
      GTY441734Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the power switch on (IG).
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      I56-8 (PAON) - Body ground Power switch on (IG) Below 1 V
      I56-16 (P-AB) - Body ground Power switch on (IG) Below 1 V
    4. Turn the power switch off.
    5. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      TEXT IN ILLUSTRATION

      *1 Air Conditioning Control Assembly
      *2 Airbag Sensor Assembly
      *3 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Air Conditioning Control Assembly)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK: Go to next step 

  8. CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY441734Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      I56-8 (PAON) - Body ground Always 1 MΩ or higher
      I56-16 (P-AB) - Body ground Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Air Conditioning Control Assembly
      *2 Airbag Sensor Assembly
      *3 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Air Conditioning Control Assembly)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK → See step   18 

  9. CHECK CONNECTORS 
    1. Turn the power switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly and air conditioning control assembly.

      OK

      The connectors are properly connected.

      HINT: 

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly and air conditioning control assembly.
    5. Check that the terminals of the connectors are not damaged.

      OK

      The terminals are not deformed or damaged.

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK: Go to next step 

  10. CHECK INSTRUMENT PANEL WIRE (OPEN) 
    1. Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.
      GTY425520Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I56-8 (PAON) - I56-16 (P-AB) Always Below 1 Ω
    3. Disconnect the service wire from connector B.
      TEXT IN ILLUSTRATION

      *1 Air Conditioning Control Assembly
      *2 Airbag Sensor Assembly
      *3 Instrument Panel Wire
      *4 Service Wire
      *a Front view of wire harness connector
      (to Airbag Sensor Assembly)
      *b Front view of wire harness connector
      (to Air Conditioning Control Assembly)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK: Go to next step 

  11. CHECK INSTRUMENT PANEL WIRE (SHORT) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY441734Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      I56-8 (PAON) - I56-16 (P-AB) Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Air Conditioning Control Assembly
      *2 Airbag Sensor Assembly
      *3 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Air Conditioning Control Assembly)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK: Go to next step 

  12. CHECK INSTRUMENT PANEL WIRE (SHORT TO B+) 
    1. Connect the cable to the negative (-) auxiliary battery terminal.
      GTY441734Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the power switch on (IG).
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      I56-8 (PAON) - Body ground Power switch on (IG) Below 1 V
      I56-16 (P-AB) - Body ground Power switch on (IG) Below 1 V
    4. Turn the power switch off.
    5. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      TEXT IN ILLUSTRATION

      *1 Air Conditioning Control Assembly
      *2 Airbag Sensor Assembly
      *3 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Air Conditioning Control Assembly)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK: Go to next step 

  13. CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY441734Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      I56-8 (PAON) - Body ground Always 1 MΩ or higher
      I56-16 (P-AB) - Body ground Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Air Conditioning Control Assembly
      *2 Airbag Sensor Assembly
      *3 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Air Conditioning Control Assembly)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK: Go to next step 

  14. CHECK AIR CONDITIONING CONTROL ASSEMBLY (SOURCE VOLTAGE) 
    1. Connect the cable to the negative (-) auxiliary battery terminal.
      GTY441667Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the power switch on (IG).
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      I56-2 (IG+) - Body ground Power switch on (IG) 11 to 14 V
    4. Turn the power switch off.
    5. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      TEXT IN ILLUSTRATION

      *1 Air Conditioning Control Assembly
      *2 Airbag Sensor Assembly
      *3 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Air Conditioning Control Assembly)

    NG → REPLACE WIRE HARNESS OR AUXILIARY BATTERY 

    OK: Go to next step 

  15. CHECK PASSENGER AIRBAG ON/OFF INDICATOR 
    1. Connect the connector to the air conditioning control assembly.
      GTY444121Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the cable to the negative (-) auxiliary battery terminal.
    3. Turn the power switch on (IG).
    4. Check the indicator according to the conditions in the table below.

      OK

      Terminal Connection Condition Specified Condition
      I47-23 (PAON) - Body ground Power switch on (IG) "ON" comes on
      I47-17 (P-AB) - Body ground Power switch on (IG) "OFF" comes on
    5. Turn the power switch off.
    6. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      TEXT IN ILLUSTRATION

      *1 Air Conditioning Control Assembly
      *2 Airbag Sensor Assembly
      *3 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Airbag Sensor Assembly)

    NG → See step   18 

    OK: Go to next step 

  16. CHECK DTC 
    1. Connect the connector to the airbag sensor assembly.
      GTY315873Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the cable to the negative (-) auxiliary battery terminal.
    3. Clear the DTCs stored in memory. Refer to DTC CHECK / CLEAR [08/2013 - ] .
    4. Turn the power switch off.
    5. Turn the power switch on (IG), and wait for at least 60 seconds.
    6. Check for DTCs. Refer to DTC CHECK / CLEAR [08/2013 - ] .

      OK

      DTC B1660/43 is not output.

      HINT: 

      Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.

      TEXT IN ILLUSTRATION

      *1 Air Conditioning Control Assembly
      *2 Airbag Sensor Assembly

    NG → See step   17 

    OK → See step   19 

  17. REPLACE AIRBAG SENSOR ASSEMBLY. Refer to  REMOVAL [08/2013 - ] 
  18. REPLACE AIR CONDITIONING CONTROL ASSEMBLY. Refer to  REMOVAL [08/2013 - 12/2013] 
  19. USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2013 - 12/2013] 
scientia non olet · About LEMON Manuals