LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2014 >> Avalon XLE >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Supplemental Restraint System (Diagnostic Codes & Symptom Tests) (Except Hybrid) >> Airbag System >> DTC B1610/13: Front Airbag Sensor RH Circuit Malfunction [10/2013 - ] >> Procedure

DTC B1610/13: Front Airbag Sensor RH Circuit Malfunction [10/2013 - ]: Procedure

  1. CHECK CONNECTORS 
    1. Turn the engine switch off.
    2. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor RH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

      OK

      The connectors are properly connected.

      HINT: 

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag ECU assembly and front airbag sensor RH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.
    5. Check that the terminals of the connectors are not damaged.

      OK

      The terminals are not deformed or damaged.

    NG → REPLACE WIRE HARNESS 

    OK: Go to next step 

  2. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN) 
    1. Connect the connectors that link the engine room main wire and instrument panel wire.
      GTY375685Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A37-2 (+SR) - A37-1 (-SR) Always Below 1 Ω
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *3 Service Wire
      *a Front view of wire harness connector
      (to Airbag ECU Assembly)
      *b Front view of wire harness connector
      (to Front Airbag Sensor RH)

    NG → See step   7 

    OK: Go to next step 

  3. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT) 
    1. Disconnect the service wire from connector B.
      GTY366051Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A37-2 (+SR) - A37-1 (-SR) Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *a Front view of wire harness connector
      (to Front Airbag Sensor RH)

    NG → See step   8 

    OK: Go to next step 

  4. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+) 
    1. Connect the cable to the negative (-) battery terminal.
      GTY366051Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the engine switch on (IG).
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      A37-2 (+SR) - Body ground Engine switch on (IG) Below 1 V
      A37-1 (-SR) - Body ground Engine switch on (IG) Below 1 V
    4. Turn the engine switch off.
    5. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *a Front view of wire harness connector
      (to Front Airbag Sensor RH)

    NG → See step   9 

    OK: Go to next step 

  5. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY366051Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      A37-2 (+SR) - Body ground Always 1 MΩ or higher
      A37-1 (-SR) - Body ground Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *a Front view of wire harness connector
      (to Front Airbag Sensor RH)

    NG → See step   10 

    OK: Go to next step 

  6. CHECK FRONT AIRBAG SENSOR RH 
    1. Connect the connector to the airbag ECU assembly.
      GTY320490Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Interchange the front airbag sensor RH with LH and connect the connectors.
    3. Connect the cable to the negative (-) battery terminal.
    4. Clear the DTCs stored in memory. Refer to DTC CHECK / CLEAR [10/2013 - ] .
    5. Turn the engine switch off.
    6. Turn the engine switch on (IG), and wait for at least 60 seconds.
    7. Check for DTCs. Refer to DTC CHECK / CLEAR [10/2013 - ] .

      Result

      Result Proceed to
      DTCs B1610/13 and B1615/14 are not output. A
      DTC B1615/14 is output. B
      DTC B1610/13 is output. C

      HINT: 

      Codes other than DTCs B1610/13 and B1615/14 may be output at this time, but they are not related to this check.

    8. Turn the engine switch off.
    9. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the front airbag sensor RH and LH to their original positions and connect the connectors.
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor LH
      *2 Airbag ECU Assembly

    B → See step   13 

    C → See step   12 

    A → See step   11 

  7. CHECK INSTRUMENT PANEL WIRE (OPEN) 
    1. Disconnect the instrument panel wire connector from the engine room main wire.
      GTY381512Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      The service wire has already been inserted into connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      DA4-2 (+SR) - DA4-1 (-SR) Always Below 1 Ω
    3. Disconnect the service wire from connector B.
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *3 Engine Room Main Wire
      *4 Instrument Panel Wire
      *5 Service Wire
      *a Front view of wire harness connector
      (to Airbag ECU Assembly)
      *b Front view of wire harness connector
      (to Engine Room Main Wire)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK → REPLACE ENGINE ROOM MAIN WIRE 

  8. CHECK INSTRUMENT PANEL WIRE (SHORT) 
    1. Disconnect the instrument panel wire connector from the engine room main wire.
      GTY378082Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      DA4-2 (+SR) - DA4-1 (-SR) Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *3 Engine Room Main Wire
      *4 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Engine Room Main Wire)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK → REPLACE ENGINE ROOM MAIN WIRE 

  9. CHECK INSTRUMENT PANEL WIRE (SHORT TO B+) 
    1. Disconnect the instrument panel wire connector from the engine room main wire.
      GTY378082Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the cable to the negative (-) battery terminal.
    3. Turn the engine switch on (IG).
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      DA4-2 (+SR) - Body ground Engine switch on (IG) Below 1 V
      DA4-1 (-SR) - Body ground Engine switch on (IG) Below 1 V
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *3 Engine Room Main Wire
      *4 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Engine Room Main Wire)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK → REPLACE ENGINE ROOM MAIN WIRE 

  10. CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND) 
    1. Disconnect the instrument panel wire connector from the engine room main wire.
      GTY378082Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      DA4-2 (+SR) - Body ground Always 1 MΩ or higher
      DA4-1 (-SR) - Body ground Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *3 Engine Room Main Wire
      *4 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Engine Room Main Wire)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK → REPLACE ENGINE ROOM MAIN WIRE 

  11. USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2013 - ] 
  12. REPLACE AIRBAG ECU ASSEMBLY. Refer to  REMOVAL [10/2013 - ] 
  13. REPLACE FRONT AIRBAG SENSOR RH. Refer to  REMOVAL [10/2013 - ] 
scientia non olet · About LEMON Manuals