Problem Symptoms Table
HINT:
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
MALFUNCTION SYSTEM
| Symptom | Suspected Area | See |
|---|---|---|
| Entire combination meter does not operate | Refer to troubleshooting | Refer to Entire Combination Meter does not Operate |
| Meter illumination is always dark*1 | Refer to troubleshooting | Refer to Meter Illumination is Always Dark |
| Meter illumination does not dim at night*1 | Refer to troubleshooting | Refer to Meter Illumination does not Dim at Night |
| Accessory meter does not illuminate*2 | Refer to troubleshooting | Refer to Accessory Meter does not Illuminate |
- *1: w/ Automatic Light Control System
- *2: w/ Multi-information Display
METER OR GAUGE
| Symptom | Suspected Area | See |
|---|---|---|
| Speedometer malfunction | Refer to troubleshooting | Refer to Speedometer Malfunction |
| Tachometer malfunction | Refer to troubleshooting | Refer to Tachometer Malfunction |
| Fuel receiver gauge malfunction | Refer to troubleshooting | Refer to Fuel Receiver Gauge Malfunction |
| Engine coolant temperature receiver gauge malfunction | Refer to troubleshooting | Refer to Engine Coolant Temperature Receiver Gauge Malfunction |
WARNING/INDICATOR
| Symptom | Suspected Area | See |
|---|---|---|
| Beam indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Headlight (HI-BEAM) circuit | Refer to Headlight (HI-BEAM) Circuit | |
| Light control switch circuit | Refer to Light Control Switch Circuit | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Turn indicator light does not come on | Headlight dimmer switch assembly | Refer to REMOVAL |
| Turn signal flasher assembly | Refer to REMOVAL | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Fuel level warning light does not come on | Fuel sender gauge assembly (for 2GR-FE) | Refer to INSPECTION |
| Fuel sender gauge assembly (for 1AR-FE) | Refer to INSPECTION | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Brake warning light does not come on | Refer to troubleshooting | Refer to Brake Warning Light does not Come ON |
| Brake warning light remains on | Refer to troubleshooting | Refer to Brake Warning Light Remains ON |
| SRS warning light does not come on | Refer to troubleshooting | Refer to SRS Warning Light does not Come ON |
| SRS warning light remains on | Refer to troubleshooting | Refer to SRS Warning Light Remains ON |
| Open door warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Door courtesy switch circuit | Refer to Door Courtesy Switch Circuit | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Engine oil pressure warning light does not come on | Engine oil pressure switch assembly (for 2GR-FE) | Refer to INSPECTION |
| Engine oil pressure switch assembly (for 1AR-FE) | Refer to INSPECTION | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Charge warning light does not come on | Generator assembly (for 2GR-FE) | Refer to INSPECTION |
| Generator assembly (for 1AR-FE) | Refer to INSPECTION | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| MIL does not come on | MIL circuit (for 2GR-FE) | Refer to MIL Circuit |
| MIL circuit (for 1AR-FE) | Refer to MIL Circuit | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Driver side seat belt warning light operates | Refer to troubleshooting | Refer to Driver Side Seat Belt Warning Light does not Operate |
| ABS warning light does not come on | Refer to troubleshooting | Refer to ABS Warning Light does not Come ON |
| ABS warning light remains on | Refer to troubleshooting | Refer to ABS Warning Light Remains ON |
| Power steering warning light remains on | Refer to troubleshooting | Refer to PS Warning Light Remains ON |
| Front fog light indicator light does not come on*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Front fog light circuit | Refer to Front Fog Light Circuit | |
| Light control switch circuit | Refer to Light Control Switch Circuit | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Automatic high beam indicator light does not come on*2 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Headlight (HI-BEAM) circuit | Refer to Headlight (HI-BEAM) Circuit | |
| Light control switch circuit | Refer to Light Control Switch Circuit | |
| Headlight swivel ECU assembly | Refer to REMOVAL | |
| Inner rear view mirror assembly | Refer to INSPECTION | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| HEAD indicator light does not come on*3 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Headlight relay circuit | Refer to Headlight Relay Circuit | |
| Light control switch circuit | Refer to Light Control Switch Circuit | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| TAIL indicator light does not come on*4 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Taillight relay circuit | Refer to Taillight Relay Circuit | |
| Light control switch circuit | Refer to Light Control Switch Circuit | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Cruise set indicator light does not come on*5 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Cruise set indicator light circuit | Refer to Cruise SET Indicator Light Circuit | |
| ECM (for 2GR-FE) | Refer to REMOVAL | |
| ECM (for 1AR-FE) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Maintenance required reminder light does not come on*3 | Maintenance required reminder reset procedure undone | Refer to INITIALIZATION |
| Combination meter assembly | Refer to REMOVAL | |
| AWD warning light does not come on*6 | Refer to troubleshooting | Refer to AWD Warning Light does not Come ON |
| AWD warning light remains on*6 | Refer to troubleshooting | Refer to AWD Warning Light Remains ON |
| TRAC OFF indicator light does not come on | Refer to troubleshooting | Refer to TRAC OFF Indicator Light does not Come ON |
| TRAC OFF indicator light remains on | Refer to troubleshooting | Refer to TRAC OFF Indicator Light Remains ON |
| Tire pressure warning light does not come on | Tire pressure warning light circuit | Refer to Tire Pressure Warning Light Circuit |
| Combination meter assembly | Refer to REMOVAL | |
| Washer level warning light does not come on | Washer level warning switch | Refer to INSPECTION |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Security indicator light does not come on*7 | CAN communication system (w/ Smart Key System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Security indicator light circuit (w/ Smart Key System) | Refer to Security Indicator Light Circuit | |
| Security indicator light circuit (w/o Smart Key System) | Refer to Security Indicator Light Circuit | |
| Combination meter assembly | Refer to REMOVAL | |
| Master warning light does not come on | Combination meter assembly | Refer to REMOVAL |
| Slip indicator light does not come on | Refer to troubleshooting | Refer to Slip Indicator Light does not Come ON |
| Slip indicator light remains on | Refer to troubleshooting | Refer to Slip Indicator Light Remains ON |
| Cruise main indicator light does not come on*5 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Cruise main indicator light circuit | Refer to Cruise Main Indicator Light Circuit | |
| ECM (for 2GR-FE) | Refer to REMOVAL | |
| ECM (for 1AR-FE) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Eco Driving Indicator Light does not turn on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| ECM (for 2GR-FE) | Refer to REMOVAL | |
| ECM (for 1AR-FE) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| PCS indicator light does not come on*8 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| 3rd seat indicator light does not come on*9 | Fold seat control ECU | Refer to REMOVAL |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| VSC off indicator light does not come on | Refer to troubleshooting | Refer to VSC OFF Indicator Light does not Come ON |
| VSC off indicator light remains on | Refer to troubleshooting | Refer to VSC OFF Indicator Light Remains ON |
| Dynamic radar cruise main indicator light does not come on*10 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Cruise main indicator light circuit | Refer to Cruise Main Indicator Light Circuit | |
| Driving support ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Dynamic radar cruise ready indicator light does not come on*10 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Cruise set indicator light circuit | Refer to Cruise READY Indicator Light Circuit | |
| Driving support ECU | Refer to REMOVAL | |
| Combination meter assembly | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Blind spot monitor warning light malfunction*11 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Blind spot monitor system | Refer to PROBLEM SYMPTOMS TABLE | |
| Combination meter assembly | Refer to REMOVAL |
- *1: w/ Front Fog Light
- *2: w/ Automatic High Beam System
- *3: for U.S.A.
- *4: except U.S.A.
- *5: w/ Cruise Control System
- *6: for AWD
- *7: w/ Engine Immobilizer System
- *8: w/ Pre-collision System
- *9: w/ Power Seat Type
- *10: w/ Dynamic Radar Cruise Control System
- *11: w/ Blind Spot Monitor
OTHER
| Symptom | Suspected Area | See |
|---|---|---|
| ODO/TRIP meter malfunction | Combination meter assembly | Refer to REMOVAL |
| Eco Driving Indicator Light customize screen malfunction | Combination meter assembly | Refer to REMOVAL |
| Shift position indicator malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Automatic transaxle system (for U660F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Automatic transaxle system (for U660E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Automatic transaxle system (for U760E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| ECM (for 2GR-FE) | Refer to REMOVAL | |
| ECM (for 1AR-FE) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Dynamic radar cruise control display malfunction*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| ECM (for 2GR-FE) | Refer to REMOVAL | |
| ECM (for 1AR-FE) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Operating MODE switch does not change cruise information display | Combination meter assembly | Refer to REMOVAL |
- *1: w/ Dynamic Radar Cruise Control System
BUZZER
| Symptom | Suspected Area | See |
|---|---|---|
| No buzzer sound | Harness or connector | - |
| Combination meter assembly | Refer to REMOVAL | |
| Seat belt warning buzzer does not sound | Seat belt warning buzzer setting | Refer to CUSTOMIZE PARAMETERS |
| CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Seat belt warning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Power steering warning buzzer does not sound | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Entry interior alarm does not sound*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Key reminder buzzer does not sound*2 | Refer to troubleshooting | Refer to Key Reminder Buzzer does not Sound |
| Immobilizer buzzer does not sound*3 | CAN communication system (w/ Smart Key System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Engine immobilizer system (w/ Smart Key System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Engine immobilizer system (w/o Smart Key System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Master warning buzzer does not sound | Combination meter assembly | Refer to REMOVAL |
| Radar cruise low-speed cancel buzzer does not sound*4 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Radar cruise warning buzzer does not sound*4 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL | |
| Parking brake unreleased warning buzzer does not sound | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Parking brake switch assembly | Refer to REMOVAL | |
| Harness or connector | - | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Driving with any door opened warning buzzer does not sound | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Door courtesy switch circuit | Refer to Door Courtesy Switch Circuit | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Shift down reject buzzer does not sound | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Automatic transaxle system (for U660F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Automatic transaxle system (for U660E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Automatic transaxle system (for U760E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Combination meter assembly | Refer to REMOVAL |
- *1: w/ Smart Key System
- *2: w/o Smart Key System
- *3: w/ Engine Immobilizer System
- *4: w/ Dynamic Radar Cruise Control System
ACCESSORY METER (W/ MULTI-INFORMATION DISPLAY)
| Symptom | Suspected Area | See |
|---|---|---|
| Average fuel economy malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| ECM (for 2GR-FE) | Refer to REMOVAL | |
| ECM (for 1AR-FE) | Refer to REMOVAL | |
| Harness or connector | - | |
| Drive monitor switch | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| Eco Driving Indicator Zone Display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| ECM (for 2GR-FE) | Refer to REMOVAL | |
| ECM (for 1AR-FE) | Refer to REMOVAL | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| Driving range malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Fuel sender gauge assembly (for 2GR-FE) | Refer to INSPECTION | |
| Fuel sender gauge assembly (for 1AR-FE) | Refer to INSPECTION | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| Average speed | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Drive monitor switch | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| Trip timer | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| SFI system (for 2GR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| SFI system (for 1AR-FE) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Drive monitor switch | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| Operating drive monitor switch does not change multi-information display | Harness or connector | - |
| Drive monitor switch | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| Door open display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Door courtesy switch circuit | Refer to Door Courtesy Switch Circuit | |
| Harness or connector | - | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Parking brake engaged" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Parking brake switch assembly | Refer to REMOVAL | |
| Harness or connector | - | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Maintenance Required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Maintenance required reminder reset procedure undone | Refer to INITIALIZATION |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Maintenance Required Soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Maintenance required reminder reset procedure undone | Refer to INITIALIZATION |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Resetting Oil Maintenance Data" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Maintenance required reminder reset procedure undone | Refer to INITIALIZATION |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Low Washer Fluid" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Washer level warning switch | Refer to INSPECTION |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Check VSC System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Refer to slip indicator light does not come on | Refer to Slip Indicator Light does not Come ON |
| Refer to slip indicator light remains on | Refer to Slip Indicator Light Remains ON | |
| Refer to VSV off indicator light does not come on | Refer to VSC OFF Indicator Light does not Come ON | |
| Refer to VSV off indicator light remains on | Refer to VSC OFF Indicator Light Remains ON | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Low Oil Pressure" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Engine oil pressure switch assembly (for 2GR-FE) | Refer to INSPECTION |
| Engine oil pressure switch assembly (for 1AR-FE) | Refer to INSPECTION | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Engine Coolant Hot" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Refer to engine coolant temperature receiver gauge malfunction | Refer to Engine Coolant Temperature Receiver Gauge Malfunction |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Key is not detected" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart key system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Low Smart Key Battery" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart key system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Depress brake pedal and push engine switch to start" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart key system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Shift to P position" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart key system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Automatic transaxle system (for U660F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Automatic transaxle system (for U660E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Automatic transaxle system (for U760E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Park/neutral position switch assembly (for U660F) | Refer to ON-VEHICLE INSPECTION | |
| Park/neutral position switch assembly (for U660E) | Refer to ON-VEHICLE INSPECTION | |
| Park/neutral position switch assembly (for U760E) | Refer to ON-VEHICLE INSPECTION | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Check Steering Lock System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Steering lock system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Smart key system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Steering Lock is still active" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Steering lock system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Smart key system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Check Tire Pressure System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Tire pressure warning light circuit | Refer to Tire Pressure Warning Light Circuit |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Check SRS Airbag System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Refer to SRS warning light does not come on | Refer to SRS Warning Light does not Come ON |
| Refer to SRS warning light remains on | Refer to SRS Warning Light Remains ON | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Check Brake System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Refer to brake warning light does not come on | Refer to Brake Warning Light does not Come ON |
| Refer to brake warning light remains on | Refer to Brake Warning Light Remains ON | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Check ABS" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Refer to ABS warning light does not come on | Refer to ABS Warning Light does not Come ON |
| Refer to ABS warning light remains on | Refer to ABS Warning Light Remains ON | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Key Detected in Vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart key system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Turn Power Off Key not Detected" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart key system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Depress brake pedal, touch engine switch with key" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart key system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Stop light switch | Refer to REMOVAL | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Please Stop Vehicle to Change Settings" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Auto power off to conserve battery" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart key system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Shift to P position and push engine switch to turn power off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*1 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Smart key system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Automatic transaxle system (for U660F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Automatic transaxle system (for U660E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Automatic transaxle system (for U760E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Park/neutral position switch assembly (for U660F) | Refer to ON-VEHICLE INSPECTION | |
| Park/neutral position switch assembly (for U660E) | Refer to ON-VEHICLE INSPECTION | |
| Park/neutral position switch assembly (for U760E) | Refer to ON-VEHICLE INSPECTION | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "Check PCS System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*2 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| "PCS Temporarily not Available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*2 | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| Customize setting display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Harness or connector | - | |
| Drive monitor switch | Refer to REMOVAL | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL | |
| Rear view monitor display malfunction*3 | Rear view monitor system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Harness or connector | - | |
| Accessory meter assembly | Refer to REMOVAL | |
| Outside temperature display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING |
| Ambient temperature sensor | - | |
| Air conditioning amplifier assembly | Refer to REMOVAL | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL | |
| Accessory meter assembly | Refer to REMOVAL |
- *1: w/ Smart Key System
- *2: w/ Pre-collision System
- *3: w/o Navigation System