LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2013 >> RAV4 LE, FWD >> Repair and Diagnosis >> Accessories & Equipment >> Seats >> Seats (Service Information) (Except Hybrid) (1 Of 2) >> FRONT SEAT ASSEMBLY (for Power Seat) >> Inspection [12/2012 - 10/2015] >> Procedure

Inspection [12/2012 - 10/2015]: Procedure

  1. INSPECT POWER SEAT MOTOR 
    1. Check the operation of the lumbar support motor LH.
      1. Apply battery voltage to the lumbar support motor LH connector, and check that the lumbar support motor LH operates smoothly as follows.

        OK

        Condition Specified Condition
        Battery positive (+) → Terminal 2
        Battery negative (-) → Terminal 1        		 Forward
        Battery positive (+) → Terminal 1
        Battery negative (-) → Terminal 2        		 Backward

        If the result is not as specified, replace the separate type front seatback spring assembly LH.

        GTY381777Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without wire harness connected
        (Lumbar Support Motor LH)
    2. Check the operation of the slide motor LH.
      1. Apply battery voltage to the slide motor LH connector, and check that the slide motor LH operates smoothly as follows.

        OK

        Condition Specified Condition
        Battery positive (+) → 4 (SLD+)
        Battery negative (-) → 1 (SLD-)        		 Forward
        Battery positive (+) → 1 (SLD-)
        Battery negative (-) → 4 (SLD+)        		 Backward

        If the result is not as specified, replace the separate type front seat cushion spring assembly LH.

        GTY366168Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without wire harness connected
        (Slide Motor LH)
    3. Check the operation of the front vertical motor LH.
      1. Apply battery voltage to the front vertical motor LH connector, and check that the front vertical motor LH operates smoothly as follows.

        OK

        Condition Specified Condition
        Battery positive (+) → 4 (FRV+)
        Battery negative (-) → 1 (FRV-)        		 Upward
        Battery positive (+) → 1 (FRV-)
        Battery negative (-) → 4 (FRV+)        		 Downward

        If the result is not as specified, replace the separate type front seat cushion spring assembly LH.

        GTY366169Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without wire harness connected
        (Front Vertical Motor LH)
    4. Check the operation of the reclining motor LH.
      1. Apply battery voltage to the reclining motor LH connector, and check that the reclining motor LH operates smoothly as follows.

        OK

        Condition Specified Condition
        Battery positive (+) → 4 (RCL+)
        Battery negative (-) → 1 (RCL-)        		 Forward
        Battery positive (+) → 1 (RCL-)
        Battery negative (-) → 4 (RCL+)        		 Backward

        If the result is not as specified, replace the separate type front seat cushion spring assembly LH.

        GTY366170Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without wire harness connected
        (Reclining Motor LH)
    5. Check the operation of the lifter motor LH.
      1. Apply battery voltage to the lifter motor LH connector, and check that the lifter motor LH operates smoothly as follows.

        OK

        Condition Specified Condition
        Battery positive (+) → 4 (LFT+)
        Battery negative (-) → 1 (LFT-)        		 Upward
        Battery positive (+) → 1 (LFT-)
        Battery negative (-) → 4 (LFT+)        		 Downward

        If the result is not as specified, replace the separate type front seat cushion spring assembly LH.

        GTY366165Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without wire harness connected
        (Lifter Motor LH)
scientia non olet · About LEMON Manuals