Front Passenger Side Seat Heater does not Operate: Procedure

1. Disconnect the air conditioning control assembly connector.
   Fig 1: E91 Connector Terminal Identification

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   E91-1 (+B) - Body ground	Always	11 to 14 V
   E91-2 (ACC) - Body ground	Power switch on (ACC)	11 to 14 V
   E91-9 (IG+) - Body ground	Power switch on (IG)	11 to 14 V

3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   E91-16 (GND) - Body ground	Always	Below 1 Ω

   TEXT IN ILLUSTRATION
   
   

   *a	Front view of wire harness connector (to Air Conditioning Control Assembly)

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Disconnect the seat heater control sub-assembly RH connector.
   Fig 2: Seat Heater Control Connector Terminal Identification (RH)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   L34-3 (B) - Body ground	Power switch on (IG)	11 to 14 V

3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   L34-2 (E) - Body ground	Always	Below 1 Ω

   TEXT IN ILLUSTRATION
   
   

   *a	Front view of wire harness connector (to Seat Heater Control Sub-assembly RH)

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Remove the front seat cushion heater assembly RH. Refer to REMOVAL .
2. Inspect the front seat cushion heater assembly RH. Refer to INSPECTION .

NG → See step   10 

OK: Go to next step 

1. Remove the front seat back heater assembly RH. Refer to REMOVAL .
2. Inspect the front seat back heater assembly RH. Refer to INSPECTION .

NG → See step   11 

OK: Go to next step 

1. Disconnect the E116 air conditioning amplifier assembly connectors.
2. Disconnect the L34 seat heater control sub-assembly RH connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   E116-12 (SHP+) - L34-1 (TH)	Always	Below 1 Ω
   E116-3 (TSR) - L34-5 (TDC+)	Always	Below 1 Ω
   E116-7 (SG-6) - L34-4 (TDC-)	Always	Below 1 Ω
   E116-12 (SHP+) - Body ground	Always	10 kΩ or higher
   E116-3 (TSR) - Body ground	Always	10 kΩ or higher
   E116-7 (SG-6) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Temporarily replace the seat heater control sub-assembly RH with a new or normally functioning one. Refer to REMOVAL .

NEXT: Go to next step 

1. Check the seat heater system. Refer to OPERATION CHECK .

   OK

   Seat heater system operates normally.

NG → See step   8 

OK → END (SEAT HEATER CONTROL SUB-ASSEMBLY RH WAS DEFECTIVE) 

1. Temporarily replace the air conditioning control assembly with a new or normally functioning one. Refer to REMOVAL .

NEXT: Go to next step 

1. Check the seat heater system. Refer to OPERATION CHECK .

   OK

   Seat heater system operates normally.

NG → See step   12 

OK → END (AIR CONDITIONING CONTROL ASSEMBLY WAS DEFECTIVE)