LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2013 >> Highlander SE, AWD >> Repair and Diagnosis >> Restraints >> Seat Belts >> Seat Belts (Service Information) (Except Hybrid) >> Rear No. 1 Seat Outer Belt Assembly >> Installation >> Installation

Rear No. 1 Seat Outer Belt Assembly: Installation: Installation

  1. INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY 
    1. Install the rear No. 1 seat outer belt assembly with the 2 bolts.
      Fig 1: Identifying Rear No. 1 Seat Outer Belt Assembly Bolts
      GTY198906Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Bolt <A> 

      Torque: 7.5 N*m (77 kgf*cm, 66 in.*lbf) 

      Bolt <B> 

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

    2. Connect the shoulder anchor of the rear No. 1 seat outer belt assembly with the bolt.
      Fig 2: Identifying Shoulder Anchor Of Rear No. 1 Seat Outer Belt Assembly
      GTY198905Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

    3. Check if the ELR locks.
      NOTE:

      The check should be performed with outer belt assembly installed.

      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
  2. INSTALL QUARTER PILLAR GARNISH  . Refer to INSTALLATION - Step 26
  3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)  . Refer to INSTALLATION - Step 27
  4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)  . Refer to INSTALLATION - Step 43
  5. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY 
    1. Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.
      Fig 3: Identifying Rear No. 1 Seat Outer Belt Assembly Bolt
      GTY198920Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

      NOTE:

      Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.

  6. INSTALL FRONT DECK SIDE TRIM COVER  . Refer to INSTALLATION - Step 29
  7. INSTALL NO. 2 DECK SIDE TRIM HOOK (for LH Side)  . Refer to INSTALLATION - Step 30
  8. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)  . Refer to INSTALLATION - Step 46
  9. INSTALL ROPE HOOK ASSEMBLY  . Refer to INSTALLATION - Step 31
  10. INSTALL REAR DECK TRIM COVER (for LH Side without Remote Folding Function)  . Refer to INSTALLATION - Step 32
  11. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (for LH Side with Remote Folding Function)  . Refer to INSTALLATION - Step 33
  12. INSTALL REAR POWER OUTLET SOCKET COVER (for LH Side)  . Refer to INSTALLATION - Step 1
  13. INSTALL REAR POWER POINT SOCKET ASSEMBLY (for LH Side)  . Refer to INSTALLATION - Step 2
  14. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH (for LH Side)  . Refer to INSTALLATION - Step 36
  15. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH (for RH Side)  . Refer to INSTALLATION - Step 48
  16. INSTALL SIDE TRIM COVER RH (for RH Side without Rear Automatic Air Conditioning System)  . Refer to INSTALLATION - Step 50
  17. INSTALL REAR ROOM TEMPERATURE SENSOR (for RH Side with Rear Automatic Air Conditioning System)  . Refer to INSTALLATION - Step 1
  18. INSTALL SIDE TRIM COVER LH (for LH Side without Rear Seat Entertainment System)  . Refer to INSTALLATION - Step 37
  19. INSTALL POWER OUTLET SOCKET BEZEL (for LH Side with Rear Seat Entertainment System)  . Refer to INSTALLATION - Step 38
  20. INSTALL DECK SIDE TRIM  . Refer to INSTALLATION - Step 39
  21. INSTALL DECK SIDE TRIM COVER  . Refer to INSTALLATION - Step 40
  22. INSTALL REAR SEAT SIDE GARNISH CAP (for RH Side without Rear Air Conditioning System)  . Refer to INSTALLATION - Step 53
  23. INSTALL REAR SEAT SIDE GARNISH CAP (for RH Side with Rear Air Conditioning System)  . Refer to INSTALLATION - Step 54
  24. INSTALL REAR FLOOR FINISH PLATE  . Refer to INSTALLATION - Step 55
  25. INSTALL REAR NO. 2 SEAT ASSEMBLY  . Refer to INSTALLATION - Step 1
  26. INSTALL CENTER SEAT CUSHION COVER SUB-ASSEMBLY  . Refer to INSTALLATION - Step 2
  27. CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH  See step  27
  28. CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH 
  29. INSTALL DECK FLOOR BOARD ASSEMBLY  . Refer to INSTALLATION - Step 63
  30. INSTALL REAR MAT  . Refer to INSTALLATION - Step 62
  31. INSTALL DECK SIDE TRIM BOX LH  . Refer to INSTALLATION - Step 64
  32. INSTALL REAR SEAT SIDE COVER LH  . Refer to INSTALLATION - Step 65
  33. INSTALL DECK SIDE TRIM BOX RH  . Refer to INSTALLATION - Step 66
  34. INSTALL JACK CARRIER ASSEMBLY  . Refer to INSTALLATION - Step 67
  35. INSTALL JACK ASSEMBLY  . Refer to INSTALLATION - Step 68
  36. INSTALL JACK CARRIER CUSHION  . Refer to INSTALLATION - Step 69
  37. INSTALL JACK CARRIER SUPPORT 
  38. INSTALL REAR SEAT SIDE COVER RH  . Refer to INSTALLATION - Step 71
  39. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) 
  40. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY  . Refer to INSTALLATION - Step 73
  41. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY  . Refer to INSTALLATION - Step 74
  42. INSTALL DECK BOARD ASSEMBLY  . Refer to INSTALLATION - Step 75
  43. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP 
  44. INSTALL REAR DOOR SCUFF PLATE  . Refer to INSTALLATION - Step 80
  45. INSTALL REAR NO. 1 SEAT ASSEMBLY  . Refer to INSTALLATION - Step 1
  46. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (w/ Remote Folding Function)  . Refer to INSTALLATION - Step 2
  47. INSPECT REAR SEAT SLIDE ADJUSTER LOCK  . Refer to INSTALLATION - Step 3
  48. INSTALL REAR SEAT LEG SIDE COVER  . Refer to INSTALLATION - Step 4
  49. INSTALL REAR INNER TRACK BRACKET COVER  . Refer to INSTALLATION - Step 5
  50. INSTALL REAR OUTER TRACK BRACKET COVER  . Refer to INSTALLATION - Step 6
  51. INSTALL REAR SEAT TRACK BRACKET COVER  . Refer to INSTALLATION - Step 7
  52. INSTALL REAR SEAT HEADREST ASSEMBLY  . Refer to INSTALLATION - Step 8
  53. INSTALL REAR CENTER SEAT ASSEMBLY (for LH Side) 
scientia non olet · About LEMON Manuals