LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2012 >> Sienna SE >> Repair and Diagnosis (Single Page) >> Drivelines & Axles >> Driveshaft & Universal Joints >> Drive Shaft (Service Information) >> FRONT DRIVE SHAFT ASSEMBLY (for 1AR-FE) >> Disassembly >> Disassembly

FRONT DRIVE SHAFT ASSEMBLY (for 1AR-FE): Disassembly: Disassembly

  1. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING (for LH Side) 
    1. Using a screwdriver, remove the front drive shaft hole snap ring.
      Fig 1: Removing Snap Ring
      GTY114573Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP 
    1. Using pliers, remove the front No. 2 axle inboard joint boot clamp as shown in the illustration.
      Fig 2: Removing Inboard Joint Boot No. 2 Clamp
      GTY200893Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP 
    1. Remove the front axle inboard joint boot clamp.

      HINT: 

      Perform the same procedure as for the front No. 2 axle inboard joint boot clamp.

  4. SEPARATE FRONT AXLE INBOARD JOINT BOOT 
    1. Separate the front axle inboard joint boot from the front drive inboard joint assembly.
  5. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY 
    1. Remove the grease from the front drive inboard joint assembly.
    2. Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.
      Fig 3: Identifying Front Drive Inboard & Outboard Joint Shaft Assembly Matchmarks
      GTY301842Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Matchmark
      NOTE:

      Do not use a punch for the marks.

    3. Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.
    4. Using a snap ring expander, remove the shaft snap ring.
      Fig 4: Identifying Snap Ring
      GTY154769Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Put matchmarks on the outboard joint shaft and tripod joint.
      Fig 5: Removing Tripod Joint At Front Drive Outboard Joint Shaft Assembly Using A Brass Bar & Hammer
      GTY307050Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Matchmark
      NOTE:

      Do not use a punch for the marks.

    6. Using a brass bar and a hammer, remove the tripod joint from the front drive outboard joint shaft assembly.
      NOTE:

      Do not tap the roller.

  6. REMOVE FRONT AXLE INBOARD JOINT BOOT 
    1. Remove the front axle inboard joint boot from the front drive outboard joint shaft assembly.
  7. REMOVE FRONT DRIVE SHAFT DAMPER 
    1. Using pliers, remove the front drive shaft damper clamp as shown in the illustration.
      Fig 6: Removing Front Drive Shaft Damper Clamp
      GTY205524Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the front drive shaft damper.
  8. REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP 
    1. Using pliers, remove the front No. 2 axle outboard joint boot clamp as shown in the illustration.
      Fig 7: Removing No. 2 Front Axle Outboard Joint Boot Clamp
      GTY200657Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP 
    1. Remove the front axle outboard joint boot clamp.

      HINT: 

      Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.

  10. REMOVE FRONT AXLE OUTBOARD JOINT BOOT 
    1. Remove the front axle outboard joint boot from the front drive outboard joint shaft assembly.
    2. Remove the grease from the front drive outboard joint.
  11. REMOVE FRONT DRIVE SHAFT DUST COVER LH (for LH Side) 
    1. Using SST and a press, remove the front drive shaft dust cover LH.
      Fig 8: Pressing Drive Shaft Dust Cover Off LH
      GTY189802Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09950-00020 
      NOTE:

      Be careful not to drop the front drive inboard joint assembly.

  12. REMOVE FRONT DRIVE SHAFT DUST COVER RH (for RH Side) 
    1. Using a press, remove the front drive shaft dust cover RH.
      Fig 9: Removing Drive Shaft Dust Cover Off RH
      GTY187472Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Be careful not to drop the front drive inboard joint assembly.

  13. REMOVE FRONT DRIVE SHAFT DUST COVER (for RH Side) 
    1. Using SST and a press, remove the front drive shaft dust cover.
      Fig 10: Removing Drive Shaft Dust Cover
      GTY189696Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09950-00020 
      NOTE:

      Be careful not to drop the front drive inboard joint assembly.

  14. REMOVE FRONT DRIVE SHAFT BEARING (for RH Side) 
    1. Using a snap ring expander, remove the drive shaft hole snap ring.
      Fig 11: Removing Drive Shaft Hole Snap Ring
      GTY200769Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using SST and a press, remove the front drive shaft bearing.
      Fig 12: Removing Bearing
      GTY184517Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09527-10011 
      NOTE:

      Be careful not to drop the front drive inboard joint assembly.

  15. REMOVE BEARING BRACKET HOLE SNAP RING (for RH Side) 
    1. Remove the bearing bracket hole snap ring.
scientia non olet · About LEMON Manuals