LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2012 >> Prius V >> Repair and Diagnosis >> Hybrid/Electric Powertrain >> Testing and Diagnosis >> Hybrid Control System [Diagnostic Codes (P0A78-121 - P0AA1-233)] >> Hybrid Control System >> DTC P0A7A-130: Generator Inverter Performance >> Procedure

DTC P0A7A-130: Generator Inverter Performance: Procedure

  1. CHECK DTC OUTPUT (HYBRID CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
    4. Check if DTCs are output.

      Result

      Result Proceed to
      P0A7A-203 is not output A
      P0A7A-203 is also output B
      NOTE:
      • If P0A7A-203 is output, troubleshoot it first. After completing the troubleshooting for P0A7A-203, return to perform troubleshooting for this DTC.
      • Parts repaired or replaced during troubleshooting for P0A7A-203 do not need to be re-inspected in this diagnosis procedure.
    5. Turn the power switch off.

    B → See step   29 

    A: Go to next step 

  2. CHECK DTC OUTPUT (HYBRID CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
    4. Check if DTCs are output.

      HINT: 

      • If P0A7A-203 was not output in step 1 of this diagnosis procedure, check Table 1 below.
      • If P0A7A-203 was output in step 1 of this diagnosis procedure, repair that DTC first, then check Table 2 below.

      Result

      Result Proceed to
      P0A7A-130 only is output. A
      Any of the following DTCs are also output. B
      TABLE 1

      DTC No. Relevant Diagnosis
      P0A1A (all INF codes)*1 Generator Control Module
      P0A1B (all INF codes)*1 Drive Motor "A" Control Module
      P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
      P0A3F-243 Drive Motor "A" Position Sensor Circuit
      P0A40-500 Drive Motor "A" Position Sensor Circuit Range/Performance
      P0A41-245 Drive Motor "A" Position Sensor Circuit Low
      P0A4B-253 Generator Position Sensor Circuit
      P0A4C-513 Generator Position Sensor Circuit Range/Performance
      P0A4D-255 Generator Position Sensor Circuit Low
      P0A60 (all INF codes)*1 Drive Motor "A" Phase V Current
      P0A63 (all INF codes)*1 Drive Motor "A" Phase W Current
      P0A72 (all INF codes)*1 Generator Phase V Current
      P0A75 (all INF codes)*1 Generator Phase W Current
      P0A78-266, 267, 279, 287, 306, 503, 504, 505, 506, 586, 806, 807, 808 Drive Motor "A" Inverter Performance
      P0A7A-325, 344, 517, 518, 809, 810, 811 Generator Inverter Performance
      P0A90-509 Drive Motor "A" Performance
      P0A92-521 Hybrid Generator Performance
      P0A94-442, 547, 548, 549, 554, 555, 556, 585, 587, 589, 590 DC/DC Converter Performance
      P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
      P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
      P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
      P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
      P0C76-523 Hybrid Battery System Discharge Time Too Long
      P3004-803 High Voltage Power Resource
      TABLE 2

      DTC No. Relevant Diagnosis
      P0A1A (all INF codes)*1 Generator Control Module
      P0A1B (all INF codes)*1 Drive Motor "A" Control Module
      P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
      P0A3F-243 Drive Motor "A" Position Sensor Circuit
      P0A40-500 Drive Motor "A" Position Sensor Circuit Range/Performance
      P0A41-245 Drive Motor "A" Position Sensor Circuit Low
      P0A4B-253 Generator Position Sensor Circuit
      P0A4C-513 Generator Position Sensor Circuit Range/Performance
      P0A4D-255 Generator Position Sensor Circuit Low
      P0A60 (all INF codes)*1 Drive Motor "A" Phase V Current
      P0A63 (all INF codes)*1 Drive Motor "A" Phase W Current
      P0A72-333 Generator Phase V Current
      P0A75-341 Generator Phase W Current
      P0A78-266, 267, 279, 287, 306, 503, 504, 505, 506, 586, 806, 807, 808 Drive Motor "A" Inverter Performance
      P0A7A-325, 517, 518, 809, 810, 811 Generator Inverter Performance
      P0A90-509 Drive Motor "A" Performance
      P0A94-442, 547, 548, 549, 554, 555, 556, 585, 587, 589, 590 DC/DC Converter Performance
      P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
      P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
      P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
      P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
      P0C76-523 Hybrid Battery System Discharge Time Too Long
      P3004-803 High Voltage Power Resource

      HINT: 

      • *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
      • P0A7A-130 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.
    5. Turn the power switch off.

    B → See step   30 

    A: Go to next step 

  3. CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR). Refer to  PROCEDURE - Step 4 

    NG → CONNECT SECURELY 

    OK: Go to next step 

  4. CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER). Refer to  PROCEDURE - Step 3 

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  5. CHECK GENERATOR RESOLVER. Refer to  PROCEDURE - Step 4 

    NG → See step   18 

    OK: Go to next step 

  6. CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER). Refer to  PROCEDURE - Step 5 

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  7. CHECK MOTOR RESOLVER. Refer to  PROCEDURE - Step 6 

    NG → See step   20 

    OK: Go to next step 

  8. CHECK INVERTER WITH CONVERTER ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION). Refer to  PROCEDURE - Step 9 

    B → REPLACE MALFUNCTIONING PARTS 

    C → CONNECT SECURELY 

    A: Go to next step 

  9. CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION). Refer to  PROCEDURE - Step 10 

    B → REPLACE MALFUNCTIONING PARTS 

    C → CONNECT SECURELY 

    A: Go to next step 

  10. CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1). Refer to  PROCEDURE - Step 11 

    NG → See step   25 

    OK: Go to next step 

  11. CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2). Refer to  PROCEDURE - Step 12 

    NG → See step   27 

    OK: Go to next step 

  12. CHECK FUSE (PCU). Refer to  PROCEDURE - Step 13 

    NG → See step   22 

    OK: Go to next step 

  13. CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT). Refer to  PROCEDURE - Step 14 

    NG → REPAIR OR REPLACE POWER SOURCE CIRCUIT 

    OK: Go to next step 

  14. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER). Refer to  PROCEDURE - Step 15 

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  15. CHECK POWER MANAGEMENT CONTROL ECU. Refer to  PROCEDURE - Step 16 

    NG → See step   33 

    OK: Go to next step 

  16. CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR). Refer to  PROCEDURE - Step 7 

    NG → CONNECT SECURELY 

    OK: Go to next step 

  17. CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR). Refer to  PROCEDURE - Step 8 

    NG → CONNECT SECURELY 

    OK → See step   32 

  18. CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR). Refer to  PROCEDURE - Step 9 

    NG → CONNECT SECURELY 

    OK: Go to next step 

  19. CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER). Refer to  PROCEDURE - Step 10 

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK → See step   31 

  20. CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR). Refer to  PROCEDURE - Step 11 

    NG → CONNECT SECURELY 

    OK: Go to next step 

  21. CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER). Refer to  PROCEDURE - Step 12 

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK → See step   31 

  22. CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE). Refer to  PROCEDURE - Step 23 

    NG → See step   24 

    OK: Go to next step 

  23. REPLACE INVERTER WITH CONVERTER ASSEMBLY 

    Refer to COMPONENTS

    NEXT → REPLACE FUSE (PCU) 

  24. REPAIR OR REPLACE HARNESS OR CONNECTOR 

    NEXT → REPLACE FUSE (PCU) 

  25. CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION). Refer to  PROCEDURE - Step 26 

    B → REPLACE MALFUNCTIONING PARTS 

    C → CONNECT SECURELY 

    A: Go to next step 

  26. CHECK GENERATOR CABLE. Refer to  PROCEDURE - Step 27 

    NG → See step   34 

    OK → See step   31 

  27. CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE CONNECTION CONDITION). Refer to  PROCEDURE - Step 28 

    B → REPLACE MALFUNCTIONING PARTS 

    C → CONNECT SECURELY 

    A: Go to next step 

  28. CHECK MOTOR CABLE. Refer to  PROCEDURE - Step 29 

    NG → See step   35 

    OK → See step   31 

  29. GO TO DTC CHART (P0A7A-203). Refer to  DTC P0A7A-203: Generator Inverter Performance  
  30. GO TO DTC CHART (HYBRID CONTROL SYSTEM). Refer to  DIAGNOSTIC TROUBLE CODE CHART 
  31. REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY. Refer to  COMPONENTS 
  32. REPLACE INVERTER WITH CONVERTER ASSEMBLY. Refer to  COMPONENTS 
  33. REPLACE POWER MANAGEMENT CONTROL ECU. Refer to  COMPONENTS 
  34. REPLACE GENERATOR CABLE. Refer to  COMPONENTS 
  35. REPLACE MOTOR CABLE. Refer to  COMPONENTS 
scientia non olet · About LEMON Manuals