DTC C2177/77: Initialization not Completed: Procedure

1. Check if the vehicle is located in an area such as described below:
   1. Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

      HINT: 

      If the vehicle is located in an area described above, the tire pressure warning light may turn on only in a particular area due to interfering radio frequencies.

   2. Devices using similar radio frequencies are used in the vehicle.

      OK

      Facilities, or devices that use similar radio frequencies are not located in the vicinity of the vehicle.

      HINT: 

      Radio transmission may be interrupted due to the surroundings, or devices installed by the user.

NG → CHECK IF ANY DEVICE IS INSTALLED BY USER 

OK: Go to next step 

1. Perform initialization. Refer to INITIALIZATION .

NEXT: Go to next step 

1. Turn the ignition switch off.
2. Connect Techstream to the DLC3.
3. Turn the ignition switch on (IG) and turn the tester on.
4. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
5. Check the values by referring to the table below.
   TIRE PRESSURE MONITOR
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   ID1 Tire Inflation Pressure	ID1 tire inflation pressure/ min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2 , 92.5 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi)	Actual tire inflation pressure	If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
   ID2 Tire Inflation Pressure	ID2 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2 , 92.5 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi)	Actual tire inflation pressure	If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
   ID3 Tire Inflation Pressure	ID3 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2 , 92.5 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi)	Actual tire inflation pressure	If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
   ID4 Tire Inflation Pressure	ID4 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2 , 92.5 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi)	Actual tire inflation pressure	If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
   ID5 Tire Inflation Pressure	ID5 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure / -100 kPa (-1.0 kgf/cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2 , 92.5 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi)	Actual tire inflation pressure	If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*

   HINT: 

   • *: It may take about 2 or 3 minutes until the values are displayed.
   • When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck the data.
   RESULT
   
   

   Condition	Proceed to
   Tire pressure values are not displayed.	A
   All tire pressure readings are equal to specified values.	B

B → END 

A → See step   4