DTC B1411/11: Room Temperature Sensor Circuit: Procedure

1. Connect Techstream to the DLC3.
2. Turn the ignition switch on (IG) and turn Techstream main switch on.
3. Select the item below in the Data List, and read the value displayed on Techstream.
   DATA LIST / AIR CONDITIONER
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Room Temperature sensor	Room temperature sensor / Min.: -6.5°C (20.3°F) Max.: 57.25°C (135.05°F)	Actual room temperature is displayed	Open circuit: -6.5°C (-20.3°F) Short circuit: 57.25°C (135.05°F)

   OK

   The display is as specified in the normal condition column.

   Result

   Result	Proceed to
   NG	A
   OK (Checking from PROBLEM SYMPTOMS TABLE)	B
   OK (Checking from DTC)	C

B → See step   4 

C → See step   5 

A: Go to next step 

1. Remove the room temperature sensor (for front). Refer to REMOVAL - Step 4 .
   Fig 1: Identifying D26 Connector End View

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Measure the resistance according to the value(s) in the table below.

   Standard resistance

   Tester Connection	Condition	Specified Condition
   D26-1 (+) - D26-2 (-)	10°C (50°F)	3.00 to 3.73 kΩ
   D26-1 (+) - D26-2 (-)	15°C (59°F)	2.45 to 2.88 kΩ
   D26-1 (+) - D26-2 (-)	20°C (68°F)	1.95 to 2.30 kΩ
   D26-1 (+) - D26-2 (-)	25°C (77°F)	1.60 to 1.80 kΩ
   D26-1 (+) - D26-2 (-)	30°C (86°F)	1.28 to 1.47 kΩ
   D26-1 (+) - D26-2 (-)	35°C (95°F)	1.00 to 1.22 kΩ
   D26-1 (+) - D26-2 (-)	40°C (104°F)	0.80 to 1.00 kΩ
   D26-1 (+) - D26-2 (-)	45°C (113°F)	0.65 to 0.85 kΩ
   D26-1 (+) - D26-2 (-)	50°C (122°F)	0.50 to 0.70 kΩ
   D26-1 (+) - D26-2 (-)	55°C (131°F)	0.44 to 0.60 kΩ
   D26-1 (+) - D26-2 (-)	60°C (140°F)	0.36 to 0.50 kΩ

   NOTE:

   • Touching the sensor even slightly may change the resistance value. Be sure to hold the connector of the sensor.
   • When measuring, the sensor temperature must be the same as the ambient temperature.

   HINT: 

   As the temperature increases, the resistance decreases (see the graph in illustration above).

NG → See step   6 

OK: Go to next step 

1. Disconnect the D26 sensor connector.
   Fig 2: Identifying D26 & D37 Connector End Views

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Disconnect the D37 amplifier connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance

   Tester Connection	Condition	Specified Condition
   D26-1 (+) - D37-29 (TR)	Always	Below 1 Ω
   D26-2 (-) - D37-35 (SG-4)	Always	Below 1 Ω
   D26-1 (+) - Body ground	Always	1 MΩ or higher
   D26-2 (-) - Body ground	Always	1 MΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → See step   7