LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2012 >> Camry LE >> Repair and Diagnosis >> Body & Frame >> Exterior Body Panels >> Exterior Panels / Trim (Service Information) (Except Hybrid) >> Rear Door Window Frame Moulding >> Removal >> Removal

Rear Door Window Frame Moulding: Removal: Removal

  1. PRECAUTION 
    NOTE:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work. Refer to PRECAUTION .

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected. Refer to INITIALIZATION .

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG  . Refer to DISASSEMBLY - Step 3 .
  4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL  . Refer to DISASSEMBLY - Step 4 .
  5. REMOVE REAR ARMREST ASSEMBLY  . Refer to DISASSEMBLY - Step 5 .
  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY  . Refer to DISASSEMBLY - Step 6 .
  7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP  . Refer to DISASSEMBLY - Step 8 .
  8. REMOVE REAR DOOR SERVICE HOLE COVER  . Refer to DISASSEMBLY - Step 9 .
  9. REMOVE REAR DOOR CHECK ASSEMBLY  . Refer to DISASSEMBLY - Step 10 .
  10. REMOVE REAR DOOR WEATHERSTRIP  . Refer to DISASSEMBLY - Step 11 .
  11. REMOVE REAR DOOR GLASS RUN  . Refer to DISASSEMBLY - Step 12 .
  12. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY  . Refer to DISASSEMBLY - Step 13 .
  13. REMOVE REAR DOOR QUARTER WINDOW GLASS  . Refer to DISASSEMBLY - Step 14 .
  14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY  . Refer to DISASSEMBLY - Step 15 .
  15. REMOVE REAR DOOR BELT MOULDING ASSEMBLY  . See step  15.
  16. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING 

    HINT: 

    When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

    HEATING TEMPERATURE

    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Moulding 20 to 30°C (68 to 86°F)
    NOTE:

    Do not heat the vehicle body or moulding excessively.

    1. Using a heat light, heat the rear door front window frame moulding.
    2. Using a moulding remover, disengage the clip and remove the rear door front window frame moulding.
      Fig 1: Identifying Rear Door Front Window Frame Molding Clip
      GTY320904Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Double-sided Tape
      *2 Caulking Sponge
  17. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING 
    1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.
    2. Tape a 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
      Fig 2: Removing Rear Door Upper Window Frame Molding
      GTY320082Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Area Dimension
      A 5.0 mm
      NOTE:

      Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 6 rivets.
      NOTE:
      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
      • Prying the rivets with the drill may damage the rivet installation holes or drill bit.
      • Be careful of the drilled rivets, as they may be hot.
    4. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.
    5. Disengage the guide, remove the rear door upper window frame moulding from the door frame.
scientia non olet · About LEMON Manuals