Rear Stabilizer Bar: Installation: Installation

INSTALL REAR STABILIZER BUSHING (for LH Side)

Install the rear stabilizer bushing to the outside of the stopper ring on the rear stabilizer bar as shown in the illustration.

Fig 1: Installing Rear Stabilizer Bushing (For LH Side)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

TEXT IN ILLUSTRATION

NOTE:

Install the rear stabilizer bushing so that the cutout face rearward.

INSTALL REAR STABILIZER BUSHING (for RH Side)
HINT:

Perform the same procedure as for the LH side.
INSTALL REAR NO. 1 STABILIZER BAR BRACKET (for LH Side)
1. Install the rear No. 1 stabilizer bar bracket to the rear stabilizer bar.
  
  Fig 2: Installing Rear No. 1 Stabilizer Bar Bracket (For LH Side)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  TEXT IN ILLUSTRATION
  
  Front of the Vehicle
  
  NOTE:
  Be sure to install the rear No. 1 stabilizer bar bracket in the correct direction.
INSTALL REAR NO. 1 STABILIZER BAR BRACKET (for RH Side)
HINT:

Perform the same procedure as for the LH side.
INSTALL REAR NO. 2 STABILIZER BAR BRACKET (for LH Side)
1. Install the rear No. 2 stabilizer bar bracket to the rear stabilizer bar.
  
  Fig 3: Identifying No. 2 Stabilizer Bar Bracket
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR NO. 2 STABILIZER BAR BRACKET (for RH Side)
HINT:

Perform the same procedure as for the LH side.

INSTALL REAR STABILIZER BAR

Install the rear stabilizer bar with the 4 bolts.

Fig 4: Identifying Rear Stabilizer Bar Bolts

TEXT IN ILLUSTRATION

	Bolt
	Front of the Vehicle

Torque: 31 N*m (316 kgf*cm, 23 ft.*lbf)

INSTALL REAR STABILIZER LINK ASSEMBLY LH
1. Install the rear stabilizer link assembly LH to the rear shock absorber with coil spring with the nut.
  Torque: 39 N*m (400 kgf*cm, 29 ft.*lbf)
  
  If the ball joint turns together with the nut, use a hexagon wrench to hold the stud.
2. Install the rear stabilizer link assembly LH to the rear stabilizer bar with the nut.
  Torque: 39 N*m (400 kgf*cm, 29 ft.*lbf)
  
  If the ball joint turns together with the nut, use a hexagon wrench to hold the stud.
INSTALL REAR STABILIZER LINK ASSEMBLY RH
HINT:

Perform the same procedure as for the LH side.
INSTALL NO. 2 FLOOR UNDER COVER (w/ Floor Under Cover)
1. Install the No. 2 floor under cover with the 2 bolts, 3 nuts and 2 clips.
  Bolt
  
  Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf)
  
  Nut
  
  Torque: 4.0 N*m (41 kgf*cm, 35 in.*lbf)
INSTALL NO. 1 FLOOR UNDER COVER
1. Install the No. 1 floor under cover with the 2 bolts, 3 nuts and 2 clips.
  Bolt
  
  Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf)
  
  Nut
  
  Torque: 4.0 N*m (41 kgf*cm, 35 in.*lbf)
INSTALL REAR WHEELS
Torque: 103 N*m (1049 kgf*cm, 76 ft.*lbf)