Rear Stabilizer Bar: Installation: Installation

1. Temporarily install the rear stabilizer bar with the identification mark positioned on the left side of the vehicle.
   Fig 1: Identifying Identification Mark On Rear Stabilizer Bar

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Temporarily install the rear stabilizer bar bracket LH (front side) with the bolt.
   Fig 2: Locating Rear Stabilizer Bar Bracket Bolt LH (Front Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   HINT: 

   Loosely tighten the bolt so that the bracket can be moved by hand.

1. Temporarily install the rear stabilizer bar bracket RH (front side) with the 2 bolts.
   Fig 3: Locating Rear Stabilizer Bar Bracket Bolts RH (Front Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   HINT: 

   Loosely tighten the bolts so that the bracket can be moved by hand.

1. Install the rear stabilizer bushing (LH side) to the rear stabilizer bar.
   Fig 4: Identifying Rear Stabilizer Bushing (LH Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   NOTE:

   Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown in the illustration.

1. Install the rear stabilizer bushing (RH side) to the rear stabilizer bar.
   Fig 5: Identifying Rear Stabilizer Bushing (RH Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   NOTE:

   Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown in the illustration.

1. Install the rear stabilizer bar bracket LH (rear side) with the 2 bolts.
   Fig 6: Locating Rear Stabilizer Bar Bracket Bolts LH (Rear Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

1. Install the rear stabilizer bar bracket RH (rear side) with the 2 bolts.
   Fig 7: Locating Rear Stabilizer Bar Bracket Bolts RH (Rear Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

1. Fully tighten the bolt.
   Fig 8: Locating Rear Stabilizer Bar Bracket Bolt LH (For Front Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Torque: 54 N*m (550 kgf*cm, 40 ft.*lbf) 

1. Fully tighten the 2 bolts.
   Fig 9: Locating Rear Stabilizer Bar Bracket Bolts RH (For Front Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

1. Install the rear stabilizer link assembly LH to the rear shock absorber with coil spring LH with the nut.
   Fig 10: Installing Rear Stabilizer Link Assembly (4WD)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Torque: 39 N*m (400 kgf*cm, 29 ft.*lbf) 

   HINT: 

   If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.

2. Install the rear stabilizer link assembly LH to the rear stabilizer bar with the nut.
   Fig 11: Installing Rear Stabilizer Link Assembly LH To Rear Stabilizer Bar With Nut

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Torque: 39 N*m (400 kgf*cm, 29 ft.*lbf) 

   HINT: 

   If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.

HINT: 

Perform the same procedure as the LH side.

Torque: 103 N*m (1050 kgf*cm, 76 ft.*lbf)