DTC P0351: Ignition Coil "A" Primary / Secondary Circuit; DTC P0352: Ignition Coil "B" Primary / Secondary Circuit; DTC P0353: Ignition Coil "C" Primary / Secondary Circuit; DTC P0354: Ignition Coil "D" Primary / Secondary Circuit: Procedure
WARNING: This page is about a different variant/trim than selected.
- CHECK HARNESS AND CONNECTOR (IG2 RELAY - IGNITION COIL, IGNITION COIL - BODY GROUND)
- Disconnect the ignition coil connectors.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open)
Tester Connection Condition Specified Condition B30-4 (GND) - Body ground Always Below 1 Ω B59-4 (GND) - Body ground Always Below 1 Ω B32-4 (GND) - Body ground Always Below 1 Ω B60-4 (GND) - Body ground Always Below 1 Ω - Turn the ignition switch to ON.
- Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection Condition Specified Condition B30-1 (+B) - B30-4 (GND) Ignition switch ON 11 to 14 V B59-1 (+B) - B59-4 (GND) Ignition switch ON 11 to 14 V B32-1 (+B) - B32-4 (GND) Ignition switch ON 11 to 14 V B60-1 (+B) - B60-4 (GND) Ignition switch ON 11 to 14 V - Reconnect the ignition coil connectors.
NG → REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - IGNITION COIL, IGNITION COIL - BODY GROUND)
OK: Go to next step
- CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)
- Disconnect the ignition coil connectors.
- Disconnect the ECM connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open)
Tester Connection Condition Specified Condition B30-2 (IGF) - B48-16 (IGF1) Always Below 1 Ω B59-2 (IGF) - B48-16 (IGF1) Always Below 1 Ω B32-2 (IGF) - B48-16 (IGF1) Always Below 1 Ω B60-2 (IGF) - B48-16 (IGF1) Always Below 1 Ω Standard Resistance (Check for Open)
Tester Connection Condition Specified Condition B30-3 (IGT1) - B48-2 (IGT1) Always Below 1 Ω B59-3 (IGT2) - B48-3 (IGT2) Always Below 1 Ω B32-3 (IGT3) - B48-4 (IGT3) Always Below 1 Ω B60-3 (IGT4) - B48-5 (IGT4) Always Below 1 Ω Standard Resistance (Check for Short)
Tester Connection Condition Specified Condition B30-2 (IGF) or B48-16 (IGF1) - Body ground Always 10 kΩ or higher B59-2 (IGF) or B48-16 (IGF1) - Body ground Always 10 kΩ or higher B32-2 (IGF) or B48-16 (IGF1) - Body ground Always 10 kΩ or higher B60-2 (IGF) or B48-16 (IGF1) - Body ground Always 10 kΩ or higher Standard Resistance (Check for Short)
Tester Connection Condition Specified Condition B30-3 (IGT1) or B48-2 (IGT1) - Body ground Always 10 kΩ or higher B59-3 (IGT2) or B48-3 (IGT2) - Body ground Always 10 kΩ or higher B32-3 (IGT3) or B48-4 (IGT3) - Body ground Always 10 kΩ or higher B60-3 (IGT4) or B48-5 (IGT4) - Body ground Always 10 kΩ or higher - Reconnect the ECM connector.
- Reconnect the ignition coil connectors.
NG → REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
- CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Clear the DTCs, refer to DTC CHECK / CLEAR .
- Shuffle the arrangement of the ignition coils with igniters (among No. 1 to No. 4 cylinders).NOTE:
Do not shuffle the connectors.
- Perform a simulation test.
- Enter the following menus: Powertrain / Engine / Trouble Codes.
- Read the DTCs.
Result
Result Proceed to Same DTC output A Different ignition coil DTC output B
B → See step 4
A → See step 5
- REPLACE IGNITION COIL. Refer to REMOVAL
- REPLACE ECM. Refer to REMOVAL