USB Audio System Recognition/Play Error: Procedure

1. Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.
2. Check if playable files are present on the USB device or "iPod".

   HINT: 

   Refer to System Description for playable files, refer to SYSTEM DESCRIPTION .

3. Check if the USB device is a compatible format or "iPod" is a compatible version.

   HINT: 

   Refer to System Description for compatible formats and versions, refer to SYSTEM DESCRIPTION .

   Result

   Result	Proceed to
   No playable files exist, or incompatible device format or version	A
   Playable files exist, and compatible device format or version	B

B → See step   2 

A → USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT 

1. Disconnect the E35 multi-media interface ECU connector.
2. Disconnect the E34 No. 1 stereo jack adapter assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   E34-1 - E35-4	Always	Below 1 Ω
   E34-4 - E35-1	Always	Below 1 Ω
   E34-2 - E35-3	Always	Below 1 Ω
   E34-3 - E35-2	Always	Below 1 Ω
   E34-5 - E35-5	Always	Below 1 Ω
   E34-1 - Body ground	Always	10 kΩ or higher
   E34-4 - Body ground	Always	10 kΩ or higher
   E34-2 - Body ground	Always	10 kΩ or higher
   E34-3 - Body ground	Always	10 kΩ or higher
   E34-5 - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Reconnect the E35 multi-media interface ECU connector.
2. Measure the voltage according to the value(s) in the table below.
   Fig 1: Identifying E35 Multi-Media Interface ECU Connector

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   E34-1 - E34-4	Ignition switch ACC	5 V

   TEXT IN ILLUSTRATION
   
   

   *a	Front view of wire harness connector (to No. 1 Stereo Jack Adapter Assembly)

NG → See step   8 

OK: Go to next step 

1. Delete all files in the USB device or "iPod" and format/restore it.
2. Save the data again and check if it can be played on the in-vehicle device.
   NOTE:

   Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that backup music data is available before performing this operation.

   OK

   Malfunction disappears.

NG → See step   5 

OK → END 

1. Turn the ignition switch off.

   HINT: 

   When one of these DTCs has been stored, it is necessary to turn off the ignition switch to make it possible for the vehicle to recognize a new device when it is connected.

2. Turn the ignition switch to ACC.
3. Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

   HINT: 

   • If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.
   • Refer to System Description for compatible formats and versions, refer to SYSTEM DESCRIPTION .

NEXT: Go to next step 

1. Check if USB device or "iPod" is recognized by the multi-media interface ECU, if information such as track, artist and album names are displayed on the screen.

   OK

   Malfunction disappears.

NG → See step   7 

OK → USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE