LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2010 >> Matrix S, FWD, Automatic >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Supplemental Restraint System (Diagnostic Codes (B1000/31 - B1905/74) & Circuit Tests >> Airbag System >> DTC B1630/23: Rear Airbag Sensor RH Circuit Malfunction >> Procedure

DTC B1630/23: Rear Airbag Sensor RH Circuit Malfunction: Procedure

  1. CHECK CONNECTORS 
    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
    3. Check that the connectors are properly connected to the side airbag sensor RH and the rear airbag sensor RH.

      OK

      The connectors are properly connected.

      HINT: 

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.
    5. Check that the terminals of the connectors are not damaged.

      OK

      The terminals are not deformed or damaged.

    NG → REPLACE NO. 2 FLOOR WIRE 

    OK: Go to next step 

  2. CHECK NO. 2 FLOOR WIRE (OPEN) 
    1. Using SST, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.
      Fig 1: Identifying No. 2 Floor Wire (Open) And M7 And M8 Connector Terminals
      GTY217455Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Do not forcibly insert SST into the terminals of the connector.

      • SST: 09843-18040 
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      M7-1 (BCR+) - M7-2 (BCR-) Always Below 1 Ω

    NG → REPLACE NO. 2 FLOOR WIRE 

    OK: Go to next step 

  3. CHECK NO. 2 FLOOR WIRE (SHORT TO B+) 
    1. Disconnect SST from connector C.
      Fig 2: Identifying No. 2 Floor Wire (Short To B+) And M7 Connector Terminals
      GTY231225Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the cable to the negative (-) battery terminal.
    3. Turn the ignition switch to ON.
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      M7-1 (BCR+) - Body ground Ignition switch ON Below 1 V
      M7-2 (BCR-) - Body ground Ignition switch ON Below 1 V

    NG → REPLACE NO. 2 FLOOR WIRE 

    OK: Go to next step 

  4. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND) 
    1. Turn the ignition switch off.
      Fig 3: Identifying No. 2 Floor Wire (Short To B+) And M7 Connector Terminals
      GTY231225Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      M7-1 (BCR+) - Body ground Always 1 MΩ or higher
      M7-2 (BCR-) - Body ground Always 1 MΩ or higher

    NG → REPLACE NO. 2 FLOOR WIRE 

    OK: Go to next step 

  5. CHECK REAR AIRBAG SENSOR RH 
    1. Connect the connector to the side airbag sensor RH.
      Fig 4: View Of Rear Airbag Sensor RH And Connector Terminal
      GTY131430Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Interchange the rear airbag sensor LH with RH and connect the connectors.
    3. Connect the cable to the negative (-) battery terminal.
    4. Turn the ignition switch to ON, and wait for at least 60 seconds.
    5. Clear the DTCs stored in the memory . Refer to DTC CHECK / CLEAR .
    6. Turn the ignition switch off.
    7. Turn the ignition switch to ON, and wait for at least 60 seconds.
    8. Check for DTCs . Refer to DTC CHECK / CLEAR .

      Result

      Result Proceed to
      DTC B1630/23 is output. A
      DTC B1635/24 is output. B
      DTC B1630/23 and B1635/24 are not output. C

      HINT: 

      Codes other than DTC B1630/23 and B1635/24 may be output at this time, but they are not related to this check.

    C → See step   7 

    B → See step   9 

    A: Go to next step 

  6. CHECK SIDE AIRBAG SENSOR RH 
    1. Turn the ignition switch off.
      Fig 5: Identifying Rear Airbag Sensor LH Connector Terminals
      GTY182440Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
    3. Return the rear airbag sensors LH and RH to their original positions and connect the connectors.
    4. Interchange the side airbag sensor LH with RH and connect the connectors.
    5. Connect the cable to the negative (-) battery terminal.
    6. Turn the ignition switch to ON, and wait for at least 60 seconds.
    7. Clear the DTCs stored in the memory . Refer to DTC CHECK / CLEAR .
    8. Turn the ignition switch off.
    9. Turn the ignition switch to ON, and wait for at least 60 seconds.
    10. Check for DTCs . Refer to DTC CHECK / CLEAR .

      Result

      Result Proceed to
      DTC B1630/23 and B1635/24 are not output. A
      DTC B1630/23 is output. B
      DTC B1635/24 is output. C

      HINT: 

      Codes other than DTC B1630/23 and B1635/24 may be output at this time, but they are not related to this check.

    C → See step   10 

    B → See step   8 

    A → See step   7 

  7. USE SIMULATION METHOD TO CHECK. Refer to  DIAGNOSIS SYSTEM 
  8. REPLACE CENTER AIRBAG SENSOR ASSEMBLY. Refer to  REMOVAL 
  9. REPLACE REAR AIRBAG SENSOR RH. Refer to  REMOVAL 
  10. REPLACE SIDE AIRBAG SENSOR RH. Refer to  REMOVAL 
scientia non olet · About LEMON Manuals