LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2010 >> Matrix S, FWD, Automatic >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 11 (Automatic Transmission - U341E - (Service Information)) >> Shift Lever >> Inspection >> Inspection

Shift Lever: Inspection: Inspection

WARNING: This page is about a different variant/trim than selected.
  1. INSPECT SHIFT LEVER ASSEMBLY 
    1. Measure the voltage according to the value(s) in the table below.
      Fig 1: Identifying Shift Lever Control Unit Connector Terminals
      GTY190017Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Voltage

      Tester Connection Condition Specified Condition
      6 (ACC) - 1 (E) Ignition switch ON 11 to 14 V
      6 (ACC) - 1 (E) Ignition switch ACC 11 to 14 V
      6 (ACC) - 1 (E) Ignition switch off Below 1 V
      4 (STP) - 1 (E) Brake pedal depressed 11 to 14 V
      4 (STP) - 1 (E) Brake pedal released Below 1 V
      5 (KLS+) - 1 (E) 1. Ignition switch ACC and shift lever P Below 1 V
      2. Ignition switch ACC and shift lever except P (Within approx. 1 second) 7.5 to 11 V
      3. Ignition switch ACC and shift lever except P (After approx. 2 seconds) 6 to 9.5 V
      8 (IG) - 1 (E) Ignition switch ON 11 to 14 V
      8 (IG) - 1 (E) Ignition switch off Below 1 V
      NOTE:

      Do not disconnect the shift lever assembly connector.

    2. Measure the resistance according to the value(s) in the table below.
      Fig 2: Identifying Shift Lock Control Unit Assembly Connector Terminals
      GTY201509Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (E) - Body ground Always Below 1 Ω
      NOTE:

      Do not disconnect the shift lock control unit assembly connector.

      If the result is not as specified, replace the shift lock control unit.

  2. INSPECT TRANSMISSION CONTROL SWITCH 
    1. Disconnect the transmission control switch connector of the shift lever assembly.
    2. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
      Fig 3: Identifying Transmission Control Switch Connector Terminal
      GTY226572Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Shift Position Specified Condition
      1 (NSSD) - 2 (AT3) 3 and 2 Below 1 Ω
      1 (NSSD) - 3 (ATD) Except 3 and 2 10 kΩ or higher

      If the result is not as specified, replace the shift lock control unit.

  3. INSPECT SHIFT LOCK SOLENOID 
    1. Disconnect the shift lock solenoid connector.
    2. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
      Fig 4: Identifying Shift Lock Solenoid Connector Terminals
      GTY203212Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Shift Position Specified Condition
      1 (P) - 2 (E2) P 10 kΩ or higher
      1 (P) - 2 (E2) Except P Below 1 Ω

      If the result is not as specified, replace the shift lock control unit.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 (SLS-) - 4 (SLS+) Always 112 Ω

      If the result is not as specified, replace the shift lock control unit.

scientia non olet · About LEMON Manuals