Shift And Select Lever Shaft: Reassembly: Reassembly

WARNING: This page is about a different variant/trim than selected.

INSTALL NO. 1 SELECT SPRING SEAT SHAFT SNAP RING
1. Coat the shift and select lever shaft with MP grease, and install a new snap ring onto the shift and select lever shaft using a brass bar and a hammer.
  
  Fig 1: View Of Select Spring No. 1 And Seating Shaft Snap Ring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL SELECT INNER LEVER
1. Coat the No. 1 select spring seat with MP grease.
  
  Fig 2: Identifying No. 1 Select Spring Seat, Compression Spring, Select Inner Lever, And Select Inner Lever Slotted Spring Pin
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using a pin punch (5 mm) and a hammer, install the No. 1 select spring seat, compression spring, select inner lever, and select inner lever slotted spring pin onto the shift and select lever shaft.
  Driven in depth
  
  3.0 to 4.0 mm (0.1181 to 0.1575 in.)
INSTALL INNER NO. 1 SHIFT LEVER
1. Coat the shift interlock plate and inner No. 1 shift lever with MP grease.
  
  Fig 3: Identifying Inner No. 1 Shift Lever
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using a pin punch (5 mm) and a hammer, install the shift interlock plate, inner No. 1 shift lever, and shift inner lever slotted spring pin onto the shift and select lever shaft.
  Driven in depth
  
  -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
INSTALL INNER NO. 2 SHIFT LEVER
1. Coat the inner No. 2 shift lever with MP grease.
  
  Fig 4: View Of Inner No. 2 Shift Lever
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using a pin punch (5 mm) and a hammer, install the inner No. 2 shift lever and shift inner lever slotted spring pin onto the shift and select lever shaft.
  Driven in depth
  
  1.0 to 2.0 mm (0.0394 to 0.0787 in.)
INSTALL NO. 2 SELECT SPRING SEAT
1. Coat the No. 2 select spring seat with MP grease.
  
  Fig 5: Identifying Select Spring Seat No.2
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the No. 2 select spring seat and compression spring. Using a brass bar and a hammer, install a new E-ring onto the shift and select lever shaft.
INSTALL FLOOR SHIFT CONTROL SHAFT ASSEMBLY
1. Install the floor shift control shaft assembly to the selecting bellcrank support with the spring washer and nut.
  
  Fig 6: Locating Floor Shift Control Shaft Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf)
INSTALL NO. 2 SELECTING BELLCRANK BUSHING
1. Install 2 new No. 2 selecting bellcrank bushings to the selecting bellcrank support as shown in the illustration.
  
  Fig 7: Locating No. 2 Selecting Bellcrank Bushings
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 2 SELECTING BELLCRANK DUST COVER
1. Install the No. 2 selecting bellcrank dust cover to the selecting bellcrank support.
  
  Fig 8: Locating No. 2 Selecting Bellcrank Dust Cover
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  HINT:
  
  Position the arrow mark direction as shown in the illustration.
INSTALL SELECTING BELLCRANK
1. Install the selecting bellcrank to the selecting bellcrank support.
  
  Fig 9: Locating Selecting Bellcrank
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 2 SELECTING BELLCRANK PLATE WASHER
1. Install the selecting bellcrank plate washer to the selecting bellcrank with the spring washer and nut.
  
  Fig 10: Locating No. 2 Selecting Bellcrank Plate Washer
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf)
INSTALL NO. 1 SELECTING BELLCRANK DUST COVER
1. Install the No. 1 selecting bellcrank dust cover to the selecting bellcrank.
  
  Fig 11: Locating No. 1 Selecting Bellcrank Dust Cover
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FLOOR SHIFT CONTROL BELLCRANK DUST COVER
1. Install the floor shift control bellcrank dust cover to the selecting bellcrank assembly.
  
  Fig 12: Locating Floor Shift Control Bellcrank Dust Cover
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002