Rear Crankshaft Oil Seal: Installation

INSTALL REAR CRANKSHAFT OIL SEAL
1. Apply MP grease to the lip of a new rear crankshaft oil seal.
2. Using SST and a hammer, tap in the rear crankshaft oil seal until its surface is flush with the rear oil seal retainer edge.
  SST 09223-15030, 09950-70010 (09951 -07100)
  NOTE:
  - Keep the lip free from foreign matter.
  - Do not tap on the oil seal at an angle.
INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)
1. Clean the 8 bolts and 8 bolt holes.
  
  Fig 1: Tapping Rear Crankshaft Oil Seal
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Apply adhesive to 2 or 3 threads of the 8 bolts.
  Adhesive:
  
  Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
  
  Fig 2: Applying Adhesive To Threads Of Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Using SST, hold the crankshaft.
  SST 09213-54015 (91651 -60855), 09330-00021
  
  Fig 3: Holding Crankshaft
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the front drive plate spacer.
  HINT:
  
  Align the pin of the front spacer with the pin hole of the crankshaft.
  
  Fig 4: Aligning Pin Of Front Spacer With Pin Hole Of Crankshaft
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Install the drive plate and rear drive plate spacer onto the crankshaft.
  
  Fig 5: Installing Drive Plate And Rear Drive Plate Spacer Onto Crankshaft
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. In several steps, uniformly install and tighten the 8 bolts in the sequence shown in the illustration.
  Torque: 98 N*m (999 kgf*cm, 72 ft.*lbf)
INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)
1. Clean the 8 bolts and 8 bolt holes.
  
  Fig 6: Identifying Flywheel Bolts Tightening Sequence
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Apply adhesive to the end 2 or 3 threads of the 8 bolts.
  Adhesive:
  
  Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
3. Using SST, hold the crankshaft.
  SST 09213-54015 (91651-60855), 09330-00021
  
  Fig 7: Holding Crankshaft
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. In several steps, uniformly install and tighten the 8 bolts in the sequence shown in the illustration.
  Torque: 130 N*m (1326 kgf*cm, 96 ft.*lbf)
INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)
HINT:

See INSTALLATION for E351.
INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)
HINT:

See INSTALLATION for E351.

Fig 8: Identifying Flywheel Bolts Tightening Sequence
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)
HINT:
- See INSTALLATION for U250E.
- See INSTALLATION for U140F.
INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)
HINT:

See INSTALLATION for E351.