LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2009 >> Highlander Limited, FWD >> Repair and Diagnosis >> Accessories & Equipment >> Warning Systems >> Tire & Wheel (Except Hybrid) >> Tire Pressure Warning System >> Data List/Active Test

Data List/Active Test

  1. READ DATA LIST 

    HINT:

    Using Techstream to read the DATA LIST allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Turn the ignition switch off.
    2. Connect Techstream to the DLC3.
    3. Turn the ignition switch on (IG) and turn the tester on.
    4. Enter the following menus: Chassis/Tire Pressure Monitor/Data List.
    5. Check the values by referring to the table below.

    Tire Pressure Monitor 

    TESTER DISPLAY REFERENCE

    Tester Display Measurement Item/Range Normal Condition Diagnostic Note
    Mode Status Tire pressure warning system mode/NORMAL or TEST NORMAL: Normal mode TEST: Test mode -
    Main Tire Number of main tire ID that are registered/ 0,1, 2, 3, 4, 5 0 to 5 displayed -
    Vehicle Speed Vehicle speed reading/min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed Speed indicated on the combination meter
    Registered ID1 Code Registered ID1 code/min.: 0, max.: FFFFFFF*1 The ID No. registered in the transmitter ID1 is displayed -
    Registered ID2 Code Registered ID2 code/min.: 0, max.: FFFFFFF*1 The ID No. registered in the transmitter ID2 is displayed -
    Registered ID3 Code Registered ID3 code/min.: 0, max.: FFFFFFF*1 The ID No. registered in the transmitter ID3 is displayed -
    Registered ID4 Code Registered ID4 code/min.: 0, max.: FFFFFFF*1 The ID No. registered in the transmitter ID4 is displayed -
    Registered ID5 Code Registered ID5 code/min.: 0, max.: FFFFFFF*1 The ID No. registered in the transmitter ID5 is displayed -
    ID Transmission Status ID code transmission status/FINISH or NOW FINISH or NOW -
    Initialization Switch Tire pressure warning reset switch/ON, OFF ON: Switch on
    OFF: Switch off    		 -
    ID1 Tire Inflation Pressure ID1 tire inflation pressure/
    min.: Absolute pressure/0 kPa (0 kgf/cm2 , 0 psi), Relative pressure/-100 kPa (-1.0 kgf/cm2 , -14 psi)
    max.: Absolute pressure/637.5 kPa (6.5 kgf/cm2 , 92.5 psi), Relative pressure/537.5 kPa (5.4 kgf/cm2 , 78 psi)    		 Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
    ID2 Tire Inflation Pressure ID2 tire inflation pressure /
    min.: Absolute pressure/0 kPa (0 kgf/cm2 , 0 psi), Relative pressure/-100 kPa (-1.0 kgf/cm2 , -14 psi)
    max.: Absolute pressure/637.5 kPa (6.5 kgf/cm2 , 92.5 psi), Relative pressure/537.5 kPa (5.4 kgf/cm2 , 78 psi)    		 Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
    ID3 Tire Inflation Pressure ID3 tire inflation pressure /
    min.: Absolute pressure/0 kPa (0 kgf/cm2 , 0 psi), Relative pressure/-100 kPa (-1.0 kgf/cm2 , -14 psi)
    max.: Absolute pressure/637.5 kPa (6.5 kgf/cm2 , 92.5 psi), Relative pressure/537.5 kPa (5.4 kgf/cm2 , 78 psi)    		 Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
    ID4 Tire Inflation Pressure ID4 tire inflation pressure /
    min.: Absolute pressure/0 kPa (0 kgf/cm2 , 0 psi), Relative pressure/-100 kPa (-1.0 kgf/cm2 , -14 psi)
    max.: Absolute pressure/637.5 kPa (6.5 kgf/cm2 , 92.5 psi), Relative pressure/537.5 kPa (5.4 kgf/cm2 , 78 psi)    		 Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
    ID5 Tire Inflation Pressure ID5 tire inflation pressure /
    min.: Absolute pressure/0 kPa (0 kgf/cm2 , 0 psi), Relative pressure/-100 kPa (-1.0 kgf/cm2 , -14 psi)
    max.: Absolute pressure/637.5 kPa (6.5 kgf/cm2 , 92.5 psi), Relative pressure/537.5 kPa (5.4 kgf/cm2 , 78 psi)    		 Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
    ID1 Temperature in Tire ID1 temperature in tire/min.: -40°C (-40°F), max.: 215°C (419°F) Actual tire temperature If -40°C (-40°F) is displayed, data has not been received.
    ID2 Temperature in Tire ID2 temperature in tire/min.: -40°C (-40°F), max.: 215°C (419°F) Actual tire temperature If -40°C (-40°F) is displayed, data has not been received.
    ID3 Temperature in Tire ID3 temperature in tire/min.: -40°C (-40°F), max.: 215°C (419°F) Actual tire temperature If-40°C (-40°F) is displayed, data has not been received.
    ID4 Temperature in Tire ID4 temperature in tire/min.: -40°C (-40°F), max.: 215°C (419°F) Actual tire temperature If -40°C (-40°F) is displayed, data has not been received.
    ID5 Temperature in Tire ID5 temperature in tire/min.: -40°C (-40°F), max.: 215°C (419°F) Actual tire temperature If -40°C (-40°F) is displayed, data has not been received.
    ID1 Battery Voltage ID1 battery voltage/OVER or LESS Over -
    ID2 Battery Voltage ID2 battery voltage/OVER or LESS Over -
    ID3 Battery Voltage ID3 battery voltage/OVER or LESS Over -
    ID4 Battery Voltage ID4 battery voltage/OVER or LESS Over -
    ID5 Battery Voltage ID5 battery voltage/OVER or LESS Over -
    Initialization SW Info Tire pressure warning reset switch setting information/WITH or WITHOUT With -
    ID1 Initial Threshold of Low-pressure ID1 initial threshold of low-pressure/min.: -100 kPa (-1 kgf/cm2 , -14 psi), max.: 537.5 kPa (5.4 kgf/cm2 , 78 psi) Tire pressure after initialization -
    ID2 Initial Threshold of Low-pressure ID2 initial threshold of low-pressure/min.: -100 kPa (-1 kgf/cm2 , -14 psi), max.: 537.5 kPa (5.4 kgf/cm2 , 78 psi) Tire pressure after initialization -
    ID3 Initial Threshold of Low-pressure ID3 initial threshold of low-pressure/min.: -100 kPa (-1 kgf/cm2 , -14 psi), max.: 537.5 kPa (5.4 kgf/cm2 , 78 psi) Tire pressure after initialization -
    ID4 Initial Threshold of Low-pressure ID4 initial threshold of low-pressure/min.: -100 kPa (-1 kgf/cm2 , -14 psi), max.: 537.5 kPa (5.4 kgf/cm2 , 78 psi) Tire pressure after initialization -
    ID5 Initial Threshold of Low-pressure ID5 initial threshold of low-pressure/min.: -100 kPa (-1 kgf/cm2 , -14 psi), max.: 537.5 kPa (5.4 kgf/cm2 , 78 psi) Tire pressure after initialization -
    Engine Speed Engine speed reading/min.: 0 rpm, max.: 65535 rpm Actual engine speed Engine speed indicated on the combination meter
    Number of DTC Number of DTCs recorded/min.: 0, max.: 255 0 -
    HINT:
    *1: Displayed only when the ID No. is not registered.
    *2: It may take about 2 to 3 minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2125/25 (See DTC C2121/21 NO SIGNAL FROM TRANSMITTER ID1 ).
  2. ACTIVE TEST 

    HINT:

    Using Techstream to perform ACTIVE TEST allows the meters, indicators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing ACTIVE TEST early in troubleshooting is one way to save diagnostic time. It is possible to display the DATA LIST on Techstream during ACTIVE TEST.

    1. Turn the ignition switch off.
    2. Connect Techstream to the DLC3.
    3. Turn the ignition switch on (IG) and turn the tester ON.
    4. Enter the following menus: Body/Combination Meter/Active Test.
    5. According to the display on the tester, perform the "ACTIVE TEST".

    Combination Meter 

    TESTER DISPLAY REFERENCE

    Tester Display Test Part Control Range Diagnostic Note
    Indicat. Tire Pressure Warning System Tire Pressure Warning Light Tire pressure warning light is OFF/ON Confirm that the vehicle is stopped, engine idling
scientia non olet · About LEMON Manuals