Transmission Control Cable: Installation

WARNING: This page is about a different variant/trim than selected.

INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
NOTE: Before installing the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in N.

Fig 1: Pushing Lock Piece Into Adjuster Case
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Put the transmission control cable into the cabin and connect the transmission control cable with the 2 nuts.
  Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)
  
  Fig 2: Locating Nuts And Transmission Control Cable Assembly From Body
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the transmission control cable bracket to the rear engine mounting insulator with the nut.
  Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)
  
  Fig 3: Locating Nut And Rear Engine Mounting Insulator
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Connect the transmission control cable to the transmission control cable bracket with a new clip.
4. Connect the transmission control cable to the control shaft lever with the nut.
  Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf)
  
  Fig 4: Locating Nut And Transmission Control Cable Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper until the stopper clicks twice.
  
  Fig 5: Turning Nut Of Transmission Control Cable
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Install the outer part of the transmission control cable to the shift lever retainer. Check that the spring is positioned at "A" and push in the stopper.
  
  Fig 6: Checking Spring "A" And Push In Stopper
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  HINT:
  
  If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.
7. Install the cable end to the shift lever assembly.
  NOTE:
  - Check that the lock piece is pulled up.
  - Install the cable end all the way to the base of the pin.
  Fig 7: Identifying Lock Piece
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. Push the lock piece into the adjuster case.
  NOTE: Securely push in the lock piece until it locks.
  
  Fig 8: Pushing Lock Piece Into Adjuster Case
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR
1. Install the front No. 1 floor heat insulator with the 3 nuts.
  Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
INSTALL CENTER EXHAUST PIPE ASSEMBLY (See INSTALLATION )
INSTALL ENGINE UNDER COVER LH
INSTALL AIR CLEANER CASE (See INSTALLATION )

Fig 9: Locating Nuts And Front No 1 Floor Heat Insulator
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL AIR CLEANER CAP SUB-ASSEMBLY (See INSTALLATION )
INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (See INSTALLATION )
INSTALL CONSOLE BOX ASSEMBLY (See INSTALLATION )
INSTALL CONSOLE BOX CARPET (See INSTALLATION )
INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY (See INSTALLATION )
INSTALL FRONT NO. 1 CONSOLE BOX INSERT (See INSTALLATION )
INSTALL FRONT NO. 2 CONSOLE BOX INSERT (See INSTALLATION )
INSTALL INSTRUMENT PANEL BOX ASSEMBLY (See INSTALLATION )
INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (See INSTALLATION )
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (See INSTALLATION )
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH (See INSTALLATION )
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH (See INSTALLATION )
INSPECT SHIFT LEVER POSITION (See ADJUSTMENT )
ADJUST SHIFT LEVER POSITION (See ADJUSTMENT )