Parking Brake Assembly: Reassembly

1. Apply high temperature grease to the backing plate which makes contact with the shoe.

1. Apply adhesive to the threads of the parking brake shoe guide plate set bolt.

   Adhesive: Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent 

2. Install the parking brake shoe guide plate with the parking brake shoe guide plate set bolt.

   Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf) 

   Fig 1: Installing Parking Brake Shoe Guide Plate

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the parking brake shoe lever and shim to the No. 2 parking brake shoe assembly with a new C-washer.
   Fig 2: Locating C-Washer

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using a feeler gauge, measure the clearance between the No. 2 parking brake shoe assembly and parking brake shoe lever.

   Standard clearance: Less than 0.35 mm (0.014 in.) 

   If the clearance is not as specified, replace the shim with one of the correct size.

   Fig 3: Measuring Clearance Between No. 2 Parking Brake Shoe Assembly And Parking Brake Shoe Lever

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using needle-nose pliers, connect the No. 3 parking brake cable assembly to the parking brake shoe lever.
   Fig 4: Connecting Parking Brake No. 3 Cable Assembly To Parking Brake Shoe Lever

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the No. 2 parking brake shoe assembly with the parking brake shoe hold down spring No. 2 pin, the parking brake shoe hold down spring No. 2 cup, the parking brake shoe hold down spring and the parking brake shoe hold down spring No. 1 cup.
   Fig 5: Installing No. 2 Parking Brake Shoe Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Engage the claw of the parking brake shoe hold down spring No. 1 cup to the No. 2 parking brake shoe assembly.

1. Apply high temperature grease to the parking brake adjusting screw as shown in the illustration.
   Fig 6: Locating High Temperature Grease Apply Area Of Parking Brake Adjusting Screw

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the parking brake shoe return tension No. 2 spring to the No. 1 parking brake shoe assembly and the No. 2 parking brake shoe assembly.
   Fig 7: Identifying Parking Brake Shoe Return Tension No. 2 Spring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly and the No. 2 parking brake shoe assembly.

1. Install the No. 1 parking brake shoe assembly with the parking brake shoe hold down spring No. 1 pin, parking brake shoe hold down spring No. 2 cup, parking brake shoe hold down spring and parking brake shoe hold down spring No. 1 cup.
   Fig 8: Installing No. 1 Parking Brake Shoe Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Attach the parking brake shoe strut and the parking brake shoe strut compression spring to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly.

1. Using needle-nose pliers, install the 2 parking brake shoe return tension No. 1 springs.

   HINT:

   First install the front side spring and then the rear side spring.

   Fig 9: Locating Parking Brake Shoe Strut Compression Spring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Check that each part is installed properly.
   Fig 10: Checking Parking Brake Installation

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Align the matchmarks and install the rear disc.

1. Temporarily install the hub nuts.
2. Remove the shoe adjusting hole plug.
3. Turn the adjuster and expand the shoes until the disc locks.
4. Contract the shoe adjuster until the disc rotates smoothly.

   Standard: Return 8 notches 

5. Check that the shoe has no brake drag.
6. Install the shoe adjusting hole plug.
   Fig 11: Adjusting Parking Brake Shoe Clearance

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the rear disc brake caliper assembly with the 2 bolts.

   Torque: 62 N*m (632 kgf*cm, 46 ft.*lbf) 

   Fig 12: Locating Rear Disc Brake Caliper Assembly Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Torque: 103 N*m (1,050 kgf*cm, 76 ft.*lbf)