Inspection Procedure

HINT:

• If DTC P0011 or P0012 is displayed, check the intake camshaft circuit for the right Dank VVT system (bank 1).
• Bank 1 refers to the bank that includes cylinder No. 1.
• If DTC P0021 or P0022 is displayed, check the intake camshaft circuit for the left bank VVT system (bank 2).
• Bank 2 refers to the bank that does not include cylinder No. 1.
• Read freeze frame data using Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (See DTC CHECK/CLEAR  ).

1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022) 
   1. Connect Techstream to the DLC3.
   2. Turn the ignition switch to ON and turn the tester on.
   3. Enter the following menus: Powertrain/Engine/Trouble Codes.
   4. Read the DTCs.

      Result 

      DTC OUTPUT RESULT
      
      

      Display (DTC Output)	Proceed to
      P0011, P0012, P0021 or P0022	A
      P0011, P0012, P0021 or P0022 and other DTCs	B

      HINT:

      If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.

      B: GO TO DTC CHART 

      A: Go to next step 

2. PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV) 
   1. Connect Techstream to the DLC3.
   2. Start the engine and turn the tester on.
   3. Warm up the engine.
   4. Enter the following menus: Powertrain/Engine/Active Test/Control the VVT System (Bank 1) or Control the VVT System (Bank 2).
   5. Check the engine speed while operating the Oil Control Valve (OCV) using the tester.

      OK 

      ENGINE SPEED CONDITIONS
      
      

      Tester Operation	Specified Condition
      OCV OFF	Normal engine speed
      OCV ON	Engine idles roughly or stalls (soon after OCV switched from OFF to ON)

      NG: Go to step  4

      OK: Go to next step 

3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022) 
   1. Connect Techstream to the DLC3.
   2. Turn the ignition switch to ON and turn the tester on.
   3. Clear the DTCs.
   4. Start the engine and warm it up.
   5. Switch the ECM from normal mode to check mode using the tester.
   6. Drive the vehicle for more than 10 minutes.
   7. Read the DTCs using the tester.

      OK: 

      No DTC output. 

      NG: Go to step 4 

      OK: END 

4. CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN) 
   1. Remove the cylinder head covers RH and LH.
   2. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.
   3. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

      If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

      OK: 

      Timing marks on camshaft timing gears are aligned as shown in the illustration. 

   4. Reinstall the cylinder head cover.

      NG: ADJUST VALVE TIMING 

      Fig 1: Identifying Timing Marks Of Camshaft Timing Gears And Bearing Cap

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      OK: Go to next step 

5. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV) 
   1. Remove the OCV for intake camshaft.
   2. Measure the resistance between the terminals of the OCV.

      Standard resistance 

      RESISTANCE SPECIFIED CONDITIONS
      
      

      Tester Connection	Condition	Specified Condition
      1 - 2	20°C (68°F)	6.9 to 7.9 Ω

      Fig 2: Measuring Resistance Between Terminals Of OCV

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   3. Apply positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.

      OK: 

      Valve moves quickly. 

   4. Reinstall the OCV.

      NG: REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY 

      Fig 3: Checking OCV Operation

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      OK: Go to next step 

6. INSPECT OIL CONTROL VALVE FILTER AND PIPE 
   1. Remove the oil pipe No. 1 or No. 2.
   2. Remove the oil control valve filter.
   3. Check that the filter and pipe are not clogged.

      OK: 

      The filter and pipe are not clogged. 

      NG: REPLACE OIL CONTROL VALVE FILTER OR PIPE 

      Fig 4: Locating Oil Pipe Assembly With Mounting Bolts

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      OK: Go to next step 

7. REPLACE CAMSHAFT TIMING GEAR ASSEMBLY 
8. CHECK WHETHER DTC OUTPUT RECURS 
   1. Connect Techstream to the DLC3.
   2. Turn the ignition switch to ON and turn the tester on.
   3. Clear the DTCs.
   4. Start the engine and warm it up.
   5. Switch the ECM from normal mode to check mode using the tester.
   6. Driver the vehicle for more than 10 minutes.
   7. Read the output DTCs using Techstream.

      OK: 

      No DTC output. 

      HINT:

      DTC P0011, P0012, P0021 or P0022 is output when foreign objects in engine oil are caught in some parts of the system. These codes will stay output even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.

      OK: SYSTEM IS OK 

      NG: REPLACE ECM (See  REMOVAL   )